wolf 3d help
#1
so im am about to fire off the 89 gxl cosmo re soon but i need a little help with a starter map. the car will be tuned by my boy in chitown but for now i need something to fire up the car, idle it, and be able to rev the motor to 3500 rpm free spin to break in the bearings. here is what i got.
mild street port 13b re
gt45 turbo
3.5 inch exhaust turbo back
1200cc primary injectors, 1680 cc secondary
4 microtech,,, bosche coils
fd ignitor
apexi boost control solinoid to run off the wolf 3d ver 4.0
2 fuel pumps, one inline one in tank
sx fpr runnin 40psi base presure
any other info anyone wants or needs to know please ask as i am lost when there is a blank map. i have gone in and did some set up stuff for the crank angle sensor and what not but ya there is so much that needs to be done like all the sensor set ups and what not.
please help me fire up this beast,,,,,,,,,,,,,, motor/ turbo combo are all new . motor is studded as well.
randy
can email me at cosmopowered@hotmail.com
mild street port 13b re
gt45 turbo
3.5 inch exhaust turbo back
1200cc primary injectors, 1680 cc secondary
4 microtech,,, bosche coils
fd ignitor
apexi boost control solinoid to run off the wolf 3d ver 4.0
2 fuel pumps, one inline one in tank
sx fpr runnin 40psi base presure
any other info anyone wants or needs to know please ask as i am lost when there is a blank map. i have gone in and did some set up stuff for the crank angle sensor and what not but ya there is so much that needs to be done like all the sensor set ups and what not.
please help me fire up this beast,,,,,,,,,,,,,, motor/ turbo combo are all new . motor is studded as well.
randy
can email me at cosmopowered@hotmail.com
#2
Here are a few maps that use.
You may need to modify them.
They ran my S5 engine.
Stock engine,
Stock coils with FD ignitor for trailings
720/1000 cc
Crank Angle sensor stab ala Hitman style.
One fuel pump.
You'll need to zero out the timing and correct the ignition to work with the bosch coils.
You may need to modify them.
They ran my S5 engine.
Stock engine,
Stock coils with FD ignitor for trailings
720/1000 cc
Crank Angle sensor stab ala Hitman style.
One fuel pump.
You'll need to zero out the timing and correct the ignition to work with the bosch coils.
#4
Wolf doesn't have that cool menu setup to zero out the timing like haltech.
I take the ignition maps and make every setting -5 and zero it out that way. Reload just the ignition map when done.
Are you familiar with wolf?
I take the ignition maps and make every setting -5 and zero it out that way. Reload just the ignition map when done.
Are you familiar with wolf?
#5
yes i used to have a wolf 3.1 and now have the wolf 4.0 the car ran well after a short tuning session by louis in chicago but for some reason my wolf got a virus or something and burnt up the map chip internaly and ended up blanking the fuel and ignition maps wich blew my motor. i played with it a few times and had gotten it to fire up and run before the new ecu but now i got a blank map and only thing that i have done was set up the cals table for the crank trigger type and a few other things . i am just in no way a tuner i only do the electrical and mechanical things and i trust all my tuning needs to louis.
randy
randy
#6
Re: wolf 3d help
HI,
I'm new around here so don't really know if this is the right post. But here I go. I been looking around for some time now (3 months) for a Wolf3d base map for a close friend. Why am i posting? Cuz we are in Puerto RIco and he knows noting about English and I know very little about RX7
He has a Mazda RX7 T2 S4 completely stock accept that all sensors have been eliminated (Accept TPS and Coolant Sensor) His stock components are the turbine and injectors.
When we install stock ECU car starts and runs good, but when installing WOlf3D ECU it doesn't. We have been able to connect pc and all to verify live data.
To my best knowledge what he needs is a stock map to load on Wolf3D ECU and he should at least get the car to start.
I'm new around here so don't really know if this is the right post. But here I go. I been looking around for some time now (3 months) for a Wolf3d base map for a close friend. Why am i posting? Cuz we are in Puerto RIco and he knows noting about English and I know very little about RX7
He has a Mazda RX7 T2 S4 completely stock accept that all sensors have been eliminated (Accept TPS and Coolant Sensor) His stock components are the turbine and injectors.
When we install stock ECU car starts and runs good, but when installing WOlf3D ECU it doesn't. We have been able to connect pc and all to verify live data.
To my best knowledge what he needs is a stock map to load on Wolf3D ECU and he should at least get the car to start.
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)