Nos!!!
#21
Originally Posted by Smog Fighter' date='Jan 23 2003, 07:59 PM
I would hate for you waste precious NO2 by sending it to the exhust side of your
intake manifold. but then you have a 13B and I have a 12A... I could be wrong.
intake manifold. but then you have a 13B and I have a 12A... I could be wrong.
#23
Originally Posted by Smog Fighter' date='Jan 24 2003, 07:15 PM
I'm learning....
Was there ports between the intake and exhaust (underneath) manifolds that
were uncovered when you installed the header?
Was there ports between the intake and exhaust (underneath) manifolds that
were uncovered when you installed the header?
#24
try removing the ACV blockoff plate and start the motor.
I know it's a waste of a gasket, but if the engine starts
and runs fine, then you need to find somewhere else to
install the nitrous.
if it doesn't run (loud sucking vacuum leak), then drill & tap
the plate for noss and boost away!!
I know it's a waste of a gasket, but if the engine starts
and runs fine, then you need to find somewhere else to
install the nitrous.
if it doesn't run (loud sucking vacuum leak), then drill & tap
the plate for noss and boost away!!
#25
Originally Posted by Smog Fighter' date='Jan 24 2003, 10:44 PM
try removing the ACV blockoff plate and start the motor.
I know it's a waste of a gasket, but if the engine starts
and runs fine, then you need to find somewhere else to
install the nitrous.
if it doesn't run (loud sucking vacuum leak), then drill & tap
the plate for noss and boost away!!
I know it's a waste of a gasket, but if the engine starts
and runs fine, then you need to find somewhere else to
install the nitrous.
if it doesn't run (loud sucking vacuum leak), then drill & tap
the plate for noss and boost away!!
#26
dude the ACV blockoff plate sounds like a great idea. I have I nitrous kit in my shop...I might just do the same.
The thing is that I already have a 45DCOE weber setup and I would have to go back to the nikki.
Hey you got any tips for a dual (as in weber) direct port setup? I'm thinking about just buying a couple of nozzles and plumbing a 70hp shot thru the primary runners. ANY TIPS???
ahh I got the lake cities sidedraft manifold type...
The thing is that I already have a 45DCOE weber setup and I would have to go back to the nikki.
Hey you got any tips for a dual (as in weber) direct port setup? I'm thinking about just buying a couple of nozzles and plumbing a 70hp shot thru the primary runners. ANY TIPS???
ahh I got the lake cities sidedraft manifold type...
#27
Originally Posted by mperformance' date='Jan 25 2003, 11:51 AM
dude the ACV blockoff plate sounds like a great idea. I have I nitrous kit in my shop...I might just do the same.
The thing is that I already have a 45DCOE weber setup and I would have to go back to the nikki.
Hey you got any tips for a dual (as in weber) direct port setup? I'm thinking about just buying a couple of nozzles and plumbing a 70hp shot thru the primary runners. ANY TIPS???
ahh I got the lake cities sidedraft manifold type...
The thing is that I already have a 45DCOE weber setup and I would have to go back to the nikki.
Hey you got any tips for a dual (as in weber) direct port setup? I'm thinking about just buying a couple of nozzles and plumbing a 70hp shot thru the primary runners. ANY TIPS???
ahh I got the lake cities sidedraft manifold type...
#28
I'm thinking about buying a zex setup, for my 79 with the 86 engine and egi. It's a 55 shot, that should be ok, but i think i'll try to drill and tap into the upper manifold, just after the injectors that way it sould mix good, or would it be better to get as close to intake ports as possible???
#29
Originally Posted by '79rx7' date='Jan 27 2003, 11:34 PM
I'm thinking about buying a zex setup, for my 79 with the 86 engine and egi. It's a 55 shot, that should be ok, but i think i'll try to drill and tap into the upper manifold, just after the injectors that way it sould mix good, or would it be better to get as close to intake ports as possible???
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)