Damn! What Can It Be? The Pfc?
#121
Man I told you 4 pages back that the injectors are fucked.
I don't remember what configuration you are running, but i have stock secondary injectors still in the rail that I know are good. If you can use them, I can have them in the mail tomorrow
I don't remember what configuration you are running, but i have stock secondary injectors still in the rail that I know are good. If you can use them, I can have them in the mail tomorrow
#122
Originally Posted by turbovr6' date='Mar 3 2004, 10:02 AM
Man I told you 4 pages back that the injectors are fucked.
I don't remember what configuration you are running, but i have stock secondary injectors still in the rail that I know are good. If you can use them, I can have them in the mail tomorrow
I don't remember what configuration you are running, but i have stock secondary injectors still in the rail that I know are good. If you can use them, I can have them in the mail tomorrow
I appreciate the offer for the injectors.. I still have mine, but not even sure if I want to take the chance with them as some how my primaries stopped working.. What would you ask for them? And what do I have to do to fit them in the primary rail? You-tha-man.
#123
Ok.. I know it's been covered, and I HIGHLY doubt it would cause anything to be funky.. But which wire should the resistor go in on the secondaries? I've heard it doesn't matter but figured I'd RE-ask..
#124
I have heard the same. Doesn't matter just adds resistance to the circuit. What size resisitors are you using? I thought I heard they were supposed to be like 10ohm-10watt.
Here's a link to the thread on the OTHER forum
http://www.rx7club.com/showthread.php?s=&t...ht=resistor+10W
Here's a link to the thread on the OTHER forum
http://www.rx7club.com/showthread.php?s=&t...ht=resistor+10W
#125
Originally Posted by jeff48920' date='Mar 3 2004, 12:18 PM
I have heard the same. Doesn't matter just adds resistance to the circuit. What size resisitors are you using? I thought I heard they were supposed to be like 10ohm-10watt.
Here's a link to the thread on the OTHER forum
http://www.rx7club.com/showthread.php?s=&t...ht=resistor+10W
Here's a link to the thread on the OTHER forum
http://www.rx7club.com/showthread.php?s=&t...ht=resistor+10W
WELL, I cut the ****** out. That wouldn't be any different than just leaving it hang there correct?
I doubt HIGHLY that is has any impact on my situation... Just curious.
#126
Originally Posted by 9BASE3' date='Mar 3 2004, 03:47 PM
(1)WELL, I cut the ****** out. That wouldn't be any different than just leaving it hang there correct?
I doubt HIGHLY that is has any impact on my situation... Just curious.
(2)And what do I have to do to fit them in the primary rail?
I doubt HIGHLY that is has any impact on my situation... Just curious.
(2)And what do I have to do to fit them in the primary rail?
(2) either add an O-ring so it will seat lower, or send your rail to the guy that hooks up fuel set-ups (Keith??)
COME AWN
we have got to figure this OUT!!! ALL THE PEOPLE FOLLOWING THIS PROJECT AND HELPING AND WE CAN'T GET THIS FAWKER RUNNING!?!?!?!
did you check continuity from ECU to primaries? Main fuse to Primaries? and all the relocating relays? I know that's sounds like a lot...but should be done.
AAAAAAAAAHHHHHHHHHHHHHHHHHHHH!!!!!!!!!!!!!!!!!!!!
#127
If its hanging there it is showing a resistance to the computer and everything is good. If its cut off its showing an incomplete circuit. Check the shop manual for specified resistance and solder in a resistor.
#128
Originally Posted by 93 R1' date='Mar 3 2004, 03:03 PM
If its hanging there it is showing a resistance to the computer and everything is good. If its cut off its showing an incomplete circuit. Check the shop manual for specified resistance and solder in a resistor.
EDIT: What resistor?
#129
Originally Posted by DUB' date='Mar 3 2004, 02:52 PM
(1) correct...OPEN circuit.
(2) either add an O-ring so it will seat lower, or send your rail to the guy that hooks up fuel set-ups (Keith??)
COME AWN
we have got to figure this OUT!!! ALL THE PEOPLE FOLLOWING THIS PROJECT AND HELPING AND WE CAN'T GET THIS FAWKER RUNNING!?!?!?!
did you check continuity from ECU to primaries? Main fuse to Primaries? and all the relocating relays? I know that's sounds like a lot...but should be done.
AAAAAAAAAHHHHHHHHHHHHHHHHHHHH!!!!!!!!!!!!!!!!!!!!
(2) either add an O-ring so it will seat lower, or send your rail to the guy that hooks up fuel set-ups (Keith??)
COME AWN
we have got to figure this OUT!!! ALL THE PEOPLE FOLLOWING THIS PROJECT AND HELPING AND WE CAN'T GET THIS FAWKER RUNNING!?!?!?!
did you check continuity from ECU to primaries? Main fuse to Primaries? and all the relocating relays? I know that's sounds like a lot...but should be done.
AAAAAAAAAHHHHHHHHHHHHHHHHHHHH!!!!!!!!!!!!!!!!!!!!
I've checked everything you mentioned. All pass testing.