The Poor Mans Non-sequential
#42
Originally Posted by rico2k_uk' post='884497' date='Oct 5 2007, 06:07 AM
sorry for old post reply (good thread by the way!).. just done this mod on my uk car, and now i am getting 0 boost! help!
Go back and double check you lines. You have missed something.
#44
I've just done the above mod and everything is fine so far expect one thing....
When putting my foot down the boost starts raising very nice from about 3.5Kish but then overboosts to 1.05bar (according to the Apexi commander looks about 1.1 on Defi guage) then it cuts on me - like a fuel cut and boost drops and then if i accelerate again the same repeats just higher up the rev range - i'm getting very little det and injectors are only seeing 80%. We've changed the setting on the Apexi-commander too for the setup and checked all work done (pipes etc.) and its fine.
Running 96 FD with uprated FMIC/RAD/Blitz D/V and Apexi power FC + Commander/ Car mapped to .8bar 2 weeks ago
anyone got any suggestions on a shot term solution until i get the full conversion in a few weeks?? Other than trying to be very accurate with the right foot??
Thinking on a boost controller but am going away to Nurbugring on Thursday and dont have too much time :S lol (not going to be driving it hard but dont want any cuts) so are there any settings i can change with the PFC Comm' or will even an apexi boost control solinoid work as can get one tonight...
??? or some kind of setting i can change to save the engine??
Thanks in advance...
When putting my foot down the boost starts raising very nice from about 3.5Kish but then overboosts to 1.05bar (according to the Apexi commander looks about 1.1 on Defi guage) then it cuts on me - like a fuel cut and boost drops and then if i accelerate again the same repeats just higher up the rev range - i'm getting very little det and injectors are only seeing 80%. We've changed the setting on the Apexi-commander too for the setup and checked all work done (pipes etc.) and its fine.
Running 96 FD with uprated FMIC/RAD/Blitz D/V and Apexi power FC + Commander/ Car mapped to .8bar 2 weeks ago
anyone got any suggestions on a shot term solution until i get the full conversion in a few weeks?? Other than trying to be very accurate with the right foot??
Thinking on a boost controller but am going away to Nurbugring on Thursday and dont have too much time :S lol (not going to be driving it hard but dont want any cuts) so are there any settings i can change with the PFC Comm' or will even an apexi boost control solinoid work as can get one tonight...
??? or some kind of setting i can change to save the engine??
Thanks in advance...
#48
Originally Posted by goldk28611' post='899857' date='May 5 2008, 05:43 AM
I've just done the above mod and everything is fine so far expect one thing....
When putting my foot down the boost starts raising very nice from about 3.5Kish but then overboosts to 1.05bar (according to the Apexi commander looks about 1.1 on Defi guage) then it cuts on me - like a fuel cut and boost drops and then if i accelerate again the same repeats just higher up the rev range - i'm getting very little det and injectors are only seeing 80%. We've changed the setting on the Apexi-commander too for the setup and checked all work done (pipes etc.) and its fine.
Running 96 FD with uprated FMIC/RAD/Blitz D/V and Apexi power FC + Commander/ Car mapped to .8bar 2 weeks ago
anyone got any suggestions on a shot term solution until i get the full conversion in a few weeks?? Other than trying to be very accurate with the right foot??
Thinking on a boost controller but am going away to Nurbugring on Thursday and dont have too much time :S lol (not going to be driving it hard but dont want any cuts) so are there any settings i can change with the PFC Comm' or will even an apexi boost control solinoid work as can get one tonight...
??? or some kind of setting i can change to save the engine??
Thanks in advance...
When putting my foot down the boost starts raising very nice from about 3.5Kish but then overboosts to 1.05bar (according to the Apexi commander looks about 1.1 on Defi guage) then it cuts on me - like a fuel cut and boost drops and then if i accelerate again the same repeats just higher up the rev range - i'm getting very little det and injectors are only seeing 80%. We've changed the setting on the Apexi-commander too for the setup and checked all work done (pipes etc.) and its fine.
Running 96 FD with uprated FMIC/RAD/Blitz D/V and Apexi power FC + Commander/ Car mapped to .8bar 2 weeks ago
anyone got any suggestions on a shot term solution until i get the full conversion in a few weeks?? Other than trying to be very accurate with the right foot??
Thinking on a boost controller but am going away to Nurbugring on Thursday and dont have too much time :S lol (not going to be driving it hard but dont want any cuts) so are there any settings i can change with the PFC Comm' or will even an apexi boost control solinoid work as can get one tonight...
??? or some kind of setting i can change to save the engine??
Thanks in advance...
I got the same issue, but i like how it runs...I went back to seq until i figure out it out. I think it has something to do with our power Fc and the way its hooked up.
Thread
Thread Starter
Forum
Replies
Last Post
wickedrx7
3rd Generation Specific
1
03-24-2004 09:38 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)