For Sale 1993 R1 Rx-7
#1
13B-REW ( less than 15k miles all new block )
TurboNeticks T04 62-2 Custom Single Turbo ( just re-built less than 15k miles )
Custom Exhaust Manifold
TurboNeticks Waste Gate ( just rebuilt less than 10k miles )
Blitz Super Sound BOV
Cosmo Fuel Pump
Front mount intercooler sperco core
Apexi Power FC with Commander and Holder
Greedy Turbo Timer
3 Inch too 4.5 inch Exhaust with Greddy Muffler and resonator
After-Market Rad ( needs brazing done to fix a mount )
ACT Street / Strip clutch ( less than 5k miles )
ACT Pro Lite Fly Wheel 9.5Lbs with counter weight
SS clutch line
H&R Springs
HKS Cold Air Intake
Re-Located Battery ( Passenger Side Bin )
C's Short Shifter ( less than 10k miles )
Phantom Air / Fuel ratio gauge
Greddy Boost gauge
Mazda Speed PPF
Tranny Brace ( Dragon spec )
UnderDrive pully
Removed Power steering and AC
17 Inch Enkie Wheels 17X7
Dunlop FM901 tires near brand new
I have the Ac and some of the the power steering equipment minus the cooler line which i cut to take it out. The car also has a brand new engine wiring harness with less than 15k miles on it. It has a clarion head unit a custom fiber glass box, the box holds 4 subs. I also have another box made that hold two 8's. i have a burnt ECU for a stock computer if you wanna sell it, also a T2 LSD with ring and pinion and FD case I have a about a foot of silicon hose for the air filter. Also a diff brace that needs to be installed. some exhaust and or brace mods will need to be done so it can fit.
************************************************** ********************
I have a brand new fuel system here at my house with all SS lines 1680 CC inj new sec rail a pri rail drilled for 850s and a FPR with gauge.
I also have a 3 bar map sensor and a new 02 sensor
And i have a .84 A/R exhuast housing for the turbo
************************************************** ********************
Currently the wiring harness is damaged in the drive side fender, this is causing all kinds of problems and the car wont turn over due to this. If you push start it it will start and runs and drives ok. The only other problem is the throw-out bearing needs replaced.
$15,000 OBO
TurboNeticks T04 62-2 Custom Single Turbo ( just re-built less than 15k miles )
Custom Exhaust Manifold
TurboNeticks Waste Gate ( just rebuilt less than 10k miles )
Blitz Super Sound BOV
Cosmo Fuel Pump
Front mount intercooler sperco core
Apexi Power FC with Commander and Holder
Greedy Turbo Timer
3 Inch too 4.5 inch Exhaust with Greddy Muffler and resonator
After-Market Rad ( needs brazing done to fix a mount )
ACT Street / Strip clutch ( less than 5k miles )
ACT Pro Lite Fly Wheel 9.5Lbs with counter weight
SS clutch line
H&R Springs
HKS Cold Air Intake
Re-Located Battery ( Passenger Side Bin )
C's Short Shifter ( less than 10k miles )
Phantom Air / Fuel ratio gauge
Greddy Boost gauge
Mazda Speed PPF
Tranny Brace ( Dragon spec )
UnderDrive pully
Removed Power steering and AC
17 Inch Enkie Wheels 17X7
Dunlop FM901 tires near brand new
I have the Ac and some of the the power steering equipment minus the cooler line which i cut to take it out. The car also has a brand new engine wiring harness with less than 15k miles on it. It has a clarion head unit a custom fiber glass box, the box holds 4 subs. I also have another box made that hold two 8's. i have a burnt ECU for a stock computer if you wanna sell it, also a T2 LSD with ring and pinion and FD case I have a about a foot of silicon hose for the air filter. Also a diff brace that needs to be installed. some exhaust and or brace mods will need to be done so it can fit.
************************************************** ********************
I have a brand new fuel system here at my house with all SS lines 1680 CC inj new sec rail a pri rail drilled for 850s and a FPR with gauge.
I also have a 3 bar map sensor and a new 02 sensor
And i have a .84 A/R exhuast housing for the turbo
************************************************** ********************
Currently the wiring harness is damaged in the drive side fender, this is causing all kinds of problems and the car wont turn over due to this. If you push start it it will start and runs and drives ok. The only other problem is the throw-out bearing needs replaced.
$15,000 OBO
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)