Mix and Match
#1
I'd like to get some opinions on the best parts to use for my rebuild of a 6 port 13b from my GSL-SE. It is going to be turboed and I'd like to beef it up as much as possible using any parts (oil metering, bearings, housings, eccentric shaft etc) that can be taken from a '93 FD motor (I've been given the parts car).
Can/should I use the FD rotors since they are lower compression (9.0:1 vs 9.4:1)?
Anyone out there running a turbo on the 9.4:1 compression have a octane recommendations and/or dyno info?
To sum this up, I have a complete 6port 13b and a complete FD parts car. I'd like to use any beefier/better parts from the FD motor in my 6port, which will be turboed in this project. I understand some of the FD internals are hardened and might be better to use, I just don't know which ones fit. So, if you had the two motors (and any other parts) and wanted to end up with a better than stock, turboed 6port, what would you do?
Can/should I use the FD rotors since they are lower compression (9.0:1 vs 9.4:1)?
Anyone out there running a turbo on the 9.4:1 compression have a octane recommendations and/or dyno info?
To sum this up, I have a complete 6port 13b and a complete FD parts car. I'd like to use any beefier/better parts from the FD motor in my 6port, which will be turboed in this project. I understand some of the FD internals are hardened and might be better to use, I just don't know which ones fit. So, if you had the two motors (and any other parts) and wanted to end up with a better than stock, turboed 6port, what would you do?
#6
Originally Posted by j9fd3s' post='801505' date='Feb 13 2006, 12:49 PM
well basically you wanna use the rotors, stat bearings and eshaft in the gsl-se block then
I'm guessing you mean the rotors, bearings and eshaft from the FD? Cool, that's what I needed to know. Just to satisfy the curious, I'm pretty sure the rotor housings from the FD are trashed, while my six port is fine. I also have a bit of a sentimental attachment to the SE motor... So yeah, it doesn't make sense, but that's what I'm doing and I'm pretty excited about the eventual results.
Thanks for the info. Anyone else?
#7
Those GSL-SE ports are friggin tiny. You have lots of porting ahead of you.
I'm guessing you mean the rotors, bearings and eshaft from the FD? Cool, that's what I needed to know. Just to satisfy the curious, I'm pretty sure the rotor housings from the FD are trashed, while my six port is fine. I also have a bit of a sentimental attachment to the SE motor... So yeah, it doesn't make sense, but that's what I'm doing and I'm pretty excited about the eventual results.
Thanks for the info. Anyone else?
Originally Posted by 1gendreemer' post='801533' date='Feb 13 2006, 02:19 PM
I'm guessing you mean the rotors, bearings and eshaft from the FD? Cool, that's what I needed to know. Just to satisfy the curious, I'm pretty sure the rotor housings from the FD are trashed, while my six port is fine. I also have a bit of a sentimental attachment to the SE motor... So yeah, it doesn't make sense, but that's what I'm doing and I'm pretty excited about the eventual results.
Thanks for the info. Anyone else?
Thread
Thread Starter
Forum
Replies
Last Post
RE-tech
Rotary Engine Building, Porting & Swaps
3
11-10-2008 03:18 PM
grngtcfd3s
Interior, Exterior, Audio Mods
18
09-14-2002 12:27 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)