Peripheral Port Engine Installation
Senior Member
Joined: May 2002
Posts: 22,465
From: California
Originally Posted by banzaitoyota' date='Jan 30 2005, 12:29 PM
so who's blowing your horn?
Senior Member
Joined: Nov 2002
Posts: 3,108
Originally Posted by banzaitoyota' date='Jan 30 2005, 04:16 PM
Get back to work!
Thread Starter
Super Moderator
Joined: Jul 2002
Posts: 5,181
From: My BIG ol TURBO-DIESEL
Originally Posted by Travis R' date='Jan 31 2005, 11:56 AM
How much tuning effect is that tube going to have with it being on the upstream of the throttle?
Doesn't the butterfly valve disrupt the pressure wave?
Doesn't the butterfly valve disrupt the pressure wave?
DYNO Testing and Tuning will tell. PLus: Dont get to attached to those butterflys!
Status: Pulled HALTECH harness from car. pulled unused harness branches back and tied for future use. Found a taped over unused ground in harness!!!!! GRRRR.
Laid out some 14GA and 18GA leads in harness for future use. Incorporated stock Windhield wiper harness and Alt Harness into Haltech harness along with the mazda firewall grommet
Thread Starter
Super Moderator
Joined: Jul 2002
Posts: 5,181
From: My BIG ol TURBO-DIESEL
GMON. Still have some weldding to do on the mount. The casting outgassed really bad, so I need to grind and reweld.
The first pic today is part of the E6X harness. The harness is being secured with lacing and wrapped in BANZAI-WRAP. I had some sample gry that I am using under the dash. This harness incorporates:
1. Haltech, Unused branches are coiled neatly under the dash.
2. Wiper Harness
3. E2 Connector to Alt, maintains charging status on stock dash
4. Stock Water Temp Sensor
[attachment=27784:attachment]
This shot shows the unused branches and the BA-26 Plug to hook up Stock Coils and relay'ed power
[attachment=27785:attachment]
Here is a view of BANZAI-WRAP and a length of lacing cord
[attachment=27786:attachment]
A Close up of a Spot-Knot.
[attachment=27787:attachment]
The first pic today is part of the E6X harness. The harness is being secured with lacing and wrapped in BANZAI-WRAP. I had some sample gry that I am using under the dash. This harness incorporates:
1. Haltech, Unused branches are coiled neatly under the dash.
2. Wiper Harness
3. E2 Connector to Alt, maintains charging status on stock dash
4. Stock Water Temp Sensor
[attachment=27784:attachment]
This shot shows the unused branches and the BA-26 Plug to hook up Stock Coils and relay'ed power
[attachment=27785:attachment]
Here is a view of BANZAI-WRAP and a length of lacing cord
[attachment=27786:attachment]
A Close up of a Spot-Knot.
[attachment=27787:attachment]
Thread Starter
Super Moderator
Joined: Jul 2002
Posts: 5,181
From: My BIG ol TURBO-DIESEL
Spool of Lacing Cord. Handy stuff
[attachment=27788:attachment]
Messy Workbench
[attachment=27789:attachment]
Semi=Clean Workbench
[attachment=27790:attachment]
Final view of semi-wrapped harness with factory bulkhead gromme ready to be secured with BANZAI-WRAP to the harness
[attachment=27791:attachment]
[attachment=27788:attachment]
Messy Workbench
[attachment=27789:attachment]
Semi=Clean Workbench
[attachment=27790:attachment]
Final view of semi-wrapped harness with factory bulkhead gromme ready to be secured with BANZAI-WRAP to the harness
[attachment=27791:attachment]
