manual swap
03-22-2006, 12:42 AM
#1
Senior Member
Thread Starter
Join Date: May 2002
Location: Richardson Texas
Posts: 4,326
hey guys, first of all its nice to be back to np. you dont have to tell me how much you missed me bc i know everyone did and that would just take up to much time and space.
as i searched for threads in 2nd gen about auto to manual swaps i noticed that over the years ive made about 1,342,349,099 of them but this should be one of the last ones bc im picking up the parts on saturday to do the swap and while i know i will have a lot of questions i will try to keep them all in this thread. ok now on to my question at the moment
how will i get the flywheel onto the auto e-shaft? will it bolt right on? actually im thinking i may take the car to a shop to have the flywheel/clutch done so really what i should be asking is how should i tell the guys at the shop to put the flywheel on. thanks for the help (especially banzai, hint hint i know youve done this swap) and good luck to me
as i searched for threads in 2nd gen about auto to manual swaps i noticed that over the years ive made about 1,342,349,099 of them but this should be one of the last ones bc im picking up the parts on saturday to do the swap and while i know i will have a lot of questions i will try to keep them all in this thread. ok now on to my question at the moment
how will i get the flywheel onto the auto e-shaft? will it bolt right on? actually im thinking i may take the car to a shop to have the flywheel/clutch done so really what i should be asking is how should i tell the guys at the shop to put the flywheel on. thanks for the help (especially banzai, hint hint i know youve done this swap) and good luck to me
03-23-2006, 08:39 PM
#5
Senior Member
Thread Starter
Join Date: May 2002
Location: Richardson Texas
Posts: 4,326
im planning on just using the stock flywheel, hopefully it will be in good enough shape to use from the parts car. is the pilot bearing something that i will be able to re use?
is there anything special i will have to tell the shop that does the work? will they even be able to tell that this was not a manual car if i have installed everything but the flywheel, clutch, tranny, and driveshaft? id really rather not say anything about a manual swap bc i asked a few shops a while back about the swap and they were very turned off by the idea, especially since its a rotary and everyone is afraid of them.
is there anything special i will have to tell the shop that does the work? will they even be able to tell that this was not a manual car if i have installed everything but the flywheel, clutch, tranny, and driveshaft? id really rather not say anything about a manual swap bc i asked a few shops a while back about the swap and they were very turned off by the idea, especially since its a rotary and everyone is afraid of them.
03-23-2006, 09:25 PM
#6
Senior Member
Thread Starter
Join Date: May 2002
Location: Richardson Texas
Posts: 4,326
hey does anywhere know where i can get the manual section of the fsm? when i DLed it before i didnt get the manual trans section bc i didnt have a manual. i tried 1300cc.com and iluvmyrx7.com but couldnt find them.
03-23-2006, 10:53 PM
#7
Super Moderator
Join Date: Jul 2002
Location: My BIG ol TURBO-DIESEL
Posts: 5,181
the auto E-Shaft wont have a pilot bearing installed in it, You need it and the ppilot bearing seal. DO NOT use a USED throw out bearing either, in fact get the TII Throw out bearing. Mike? Part numbers please
03-23-2006, 11:16 PM
#8
Senior Member
Thread Starter
Join Date: May 2002
Location: Richardson Texas
Posts: 4,326
Originally Posted by banzaitoyota' post='809676' date='Mar 23 2006, 10:53 PM
the auto E-Shaft wont have a pilot bearing installed in it, You need it and the ppilot bearing seal. DO NOT use a USED throw out bearing either, in fact get the TII Throw out bearing. Mike? Part numbers please
is it ok to re use the pilot bearing from the manual parts car? i dont need the part numbers, ill just go through mazdatrix. thanks a lot.
haha, i just realized i asked "does anywhere know where i can get the..." i meant does anyone know, whoops.