2nd Generation Specific 1986-1992 Discussion

Glowing pre-cat

Old Apr 20, 2002 | 01:13 AM
  #1  
isamu's Avatar
Thread Starter
Senior Member
 
Joined: Oct 2001
Posts: 1,847
From: Marysville WA.
Default

Do you think running on one rotor would cause my little catalytic converter to get cherry red, or do you think its clogged? If I let my car warm up completely I can feel the heat with my hand if I just stick it out the drivers side door.
Old Apr 20, 2002 | 01:30 AM
  #2  
Powerpack's Avatar
Senior Member
 
Joined: Apr 2002
Posts: 233
Default

Maybe the unburned fuel of the rotor that is not working finishes its burning in the precat. Could it be?

You should disconnect the injectors of this rotor since it doesn't produce any power.
Old Apr 20, 2002 | 01:41 AM
  #3  
isamu's Avatar
Thread Starter
Senior Member
 
Joined: Oct 2001
Posts: 1,847
From: Marysville WA.
Default

Thats what I was thinking, but wasn't sure. The exhaust system is in great shape visually, looks almost new. I never did an actual compression test on the motor. I just listened to the rotors go by with the spark plugs out and heard quite a difference in sounds between the front and rear. I could only here one distinct swoosh in the rear. At first I thought two apex seals may have went to ****, but if one apex seal is not functioning it effects two of the three chambers of compression right? Is this why I only heard one distinct swoosh in the rear, when I heard three in the front? Just a thought anyways.
Old Apr 20, 2002 | 01:48 AM
  #4  
Powerpack's Avatar
Senior Member
 
Joined: Apr 2002
Posts: 233
Default

That sounds like it, but maybe the apex is sticky and doesn't sit. Have you checked through the leading plug hole, and see if all apexes are still there? If so, try to do the ATF trick. :sigh:
Old Apr 20, 2002 | 01:58 AM
  #5  
isamu's Avatar
Thread Starter
Senior Member
 
Joined: Oct 2001
Posts: 1,847
From: Marysville WA.
Default

I haven't. Do you mean looking and prodding through the hole or what? I have already purchased a rebuild kit so ripping it apart is in my destiny. I look forward to it. It is not my daily driver so I can take my time.
Old Apr 20, 2002 | 02:06 AM
  #6  
Powerpack's Avatar
Senior Member
 
Joined: Apr 2002
Posts: 233
Default

In fact, you just need a mirror and a light, and look into the hole in the mirror, lighting it using the mirror. You just have to turn the engine using the steering belt with your left hand. It's easy you'll see. It's a visual check!
Old Apr 20, 2002 | 02:11 AM
  #7  
isamu's Avatar
Thread Starter
Senior Member
 
Joined: Oct 2001
Posts: 1,847
From: Marysville WA.
Default

Sounds good. I never tried the ATF trick, probably should though.
Old Apr 20, 2002 | 02:17 AM
  #8  
Powerpack's Avatar
Senior Member
 
Joined: Apr 2002
Posts: 233
Default

Originally Posted by isamu' date='April 20 2002,00:11
Sounds good. I never tried the ATF trick, probably should though.
Go see in the FAQ forum, they explain the whole process, but there are thing to keep in mind with the ATF trick, you need to change the plugs afterwards so if you have an old set use it for this. And it may be hard on CAT converter.
Old Apr 20, 2002 | 02:25 AM
  #9  
Powerpack's Avatar
Senior Member
 
Joined: Apr 2002
Posts: 233
Default

Hey...don't worry about your rebuild kit, sooner or later it'll be in your destiny.
Old Apr 20, 2002 | 02:39 AM
  #10  
isamu's Avatar
Thread Starter
Senior Member
 
Joined: Oct 2001
Posts: 1,847
From: Marysville WA.
Default

Powerpack Posted on April 20 2002,00:25

--------------------------------------------------------------------------------

Hey...don't worry about your rebuild kit, sooner or later it'll be in your destiny.
OOOh Yeah!
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
FairlaneRX
RX-8 Discussion
5
Dec 13, 2012 12:54 AM
ill_booger
2nd Generation Specific
13
Apr 6, 2011 06:38 AM
Shane.Trammell
1st Generation Specific
3
Jan 21, 2005 12:41 PM
guyverx
2nd Generation Specific
13
Jun 1, 2003 08:00 PM
JimmyJimboJet
3rd Generation Specific
5
Dec 16, 2002 11:53 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Thread Tools
Search this Thread

All times are GMT -5. The time now is 03:57 AM.