T04r Setup
06-12-2004, 09:08 PM
#1
Senior Member
Thread Starter
Join Date: Jul 2002
Location: Fayetteville, Georgia
Posts: 2,483
I'm finally to the point where I can start finalizing everything for my turbo purchase. For those of you who don't know, I'm putting a 13b Cosmo in my FB. I've read over a lot of the terminology to figure out exactly what "V-Band" meant, and it's kinda scaring me. It sounds really complicated and expensive, but the T04R size I want from Cheapturbo only comes in tangential style-housings (dunno if that's the right way to say that) therefore requiring a v-band discharge, I believe.
Needless to say, I have ZERO experience with turbochargers, I just jumped right in with this project. So, here's my question:
What all do I need for this setup? I would really like to get a 1.00 or 1.15 a/r because I've heard such good things about that size with my (stock port) motor, especially from CP Racing, but Cheapturbo doesn't list either of those sizes. I haven't spoken with them yet, but I'm just brainstorming and wanted to see what you guys think. I'm also questioning the compressor wheel size, I assumed 80mm was the "normal" size for a T04R, but they have 66.5mm listed.
Well sorry for the novel and thanks for any advice!
P.S. I'm using a large NPR intercooler and I plan to design the exhaust manifold, any advice on planning this construction would be great as well.
Needless to say, I have ZERO experience with turbochargers, I just jumped right in with this project. So, here's my question:
What all do I need for this setup? I would really like to get a 1.00 or 1.15 a/r because I've heard such good things about that size with my (stock port) motor, especially from CP Racing, but Cheapturbo doesn't list either of those sizes. I haven't spoken with them yet, but I'm just brainstorming and wanted to see what you guys think. I'm also questioning the compressor wheel size, I assumed 80mm was the "normal" size for a T04R, but they have 66.5mm listed.
Well sorry for the novel and thanks for any advice!
P.S. I'm using a large NPR intercooler and I plan to design the exhaust manifold, any advice on planning this construction would be great as well.
06-12-2004, 09:22 PM
#2
Senior Member
Join Date: Dec 2002
Location: Rocklin, CA
Posts: 300
Cheap turbo carries the .96 A/R turbine which isn't far off from the 1.00 I do believe that they can get you the 1.15 A/R as well if that is the one you want. But I believe that you would be spooling up pretty late on stock ports with the 1.15 A/R. Just my .02 though.
Zach
Zach
06-12-2004, 09:25 PM
#3
Senior Member
Thread Starter
Join Date: Jul 2002
Location: Fayetteville, Georgia
Posts: 2,483
Originally Posted by BoostedRex' date='Jun 12 2004, 10:22 PM
Cheap turbo carries the .96 A/R turbine which isn't far off from the 1.00 I do believe that they can get you the 1.15 A/R as well if that is the one you want. But I believe that you would be spooling up pretty late on stock ports with the 1.15 A/R. Just my .02 though.
Zach
Zach
06-13-2004, 04:00 AM
#6
Senior Member
Join Date: Oct 2002
Posts: 5,547
Originally Posted by Dysfnctnl85' date='Jun 12 2004, 09:25 PM
I thought so too, but the guys at CP Racing (they have a handful of Cosmo FBs) say they get full boost at 3000rpm on stock ports.
06-13-2004, 01:50 PM
#9
Senior Member
Join Date: May 2002
Location: California
Posts: 22,465
Originally Posted by setzep' date='Jun 13 2004, 10:28 AM
I guess it depends on a lot of factors, header design, what "full boost is", timing, nos...ect.
I'd go with a 1.0 divided with a fully divided manifold.
I'd go with a 1.0 divided with a fully divided manifold.