2nd Generation Specific 1986-1992 Discussion

engine probs on FC3S

Thread Tools
 
Search this Thread
 
Old Oct 27, 2005 | 09:33 PM
  #1  
steitzybear79's Avatar
Thread Starter
Junior Member
 
Joined: Jun 2005
Posts: 6
Unhappy

I've noticed lately that my turbo isn't spooling up like normal. The engine is also blowing a lot of white smoke if I really get into the gas. It also gets very sluggish when the tach hits about 5,000 rpm. Does anyone have any suggestion s for me. I'm in need of some help, BAD!
Old Oct 28, 2005 | 08:47 AM
  #2  
RONIN FC's Avatar
Senior Member
 
Joined: Oct 2003
Posts: 1,420
From: Boston Ma.
Default

Originally Posted by steitzybear79' post='773400' date='Oct 27 2005, 10:33 PM
I've noticed lately that my turbo isn't spooling up like normal. The engine is also blowing a lot of white smoke if I really get into the gas. It also gets very sluggish when the tach hits about 5,000 rpm. Does anyone have any suggestion s for me. I'm in need of some help, BAD!
You might need a turbo. Take off your intercooler and see if it has oil in it.
Old Oct 28, 2005 | 09:31 AM
  #3  
One320B's Avatar
Senior Member
 
Joined: May 2005
Posts: 959
Default

That sounds like a busted turbo. Pull the intake system off all the way down to the turbo inlet and check the turbo... how bad is the endplay? how bad is the shaft play? pull the intercooler, check for oil in the intercooler lines, you can also check to see if there is oil on your exhaust tips...



..you said it was white smoke though and usually oil is a blueish color...white could be coolant. Has the car overheated lately at all? How many miles are on the engine?
Old Oct 28, 2005 | 01:15 PM
  #4  
steitzybear79's Avatar
Thread Starter
Junior Member
 
Joined: Jun 2005
Posts: 6
Default

The engine hasn't come close to over heating. Its got 139,000 on the motor. I've been running th car like normal and here the past couple days everything is running fine after the engine is warmed up. I'm soo confused.
Old Oct 28, 2005 | 01:24 PM
  #5  
RONIN FC's Avatar
Senior Member
 
Joined: Oct 2003
Posts: 1,420
From: Boston Ma.
Default

You take the intercooler out yet?
Old Oct 29, 2005 | 01:57 AM
  #6  
steitzybear79's Avatar
Thread Starter
Junior Member
 
Joined: Jun 2005
Posts: 6
Default

Not yet, but I figure that will be my weekend project. Its my everyday vehicle and through the week I need it so...you know how that goes. I'll be looking into it this weekend. Thanks for the help guys.
Old Nov 3, 2005 | 10:48 PM
  #7  
chrisgen2's Avatar
Junior Member
 
Joined: Oct 2004
Posts: 7
Default

You should check the compression levels in your rotor chambers.

-I had a similar problem, blowing a lot of white smoke, a strange hesitation on the rpm ride, and it turned out that I had zero compression in one of my chambers due to an apex seal breaking off the rotor and ripping around the housing... it was not a good look.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
gaponte
3rd Generation Specific
7
Jun 22, 2007 06:36 PM
RX7_2ner
2nd Generation Specific
2
Nov 16, 2003 05:51 PM
RotaryBoy88
2nd Generation Specific
6
Aug 3, 2002 12:54 PM
prometheosophy
2nd Generation Specific
15
May 10, 2002 12:25 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 



All times are GMT -5. The time now is 09:19 PM.