FC 13B-RE project part out!
Thread Starter
Senior Member
Joined: Aug 2002
Posts: 1,081
From: Reno,NV
Ok have huge list to put up will post some pics that show the parts but putting pics to each part would be huge!!! I you want the part pm me and I'll do my best to send you a pic of what you want to see..some of it is already off the car and can be sent out quickly. If I can I would like to sell these as a package and the prices will be pretty good.
Turbonetics T04E dual BB .57 p trim w/ custom 1.0 hotside w/ heat coating by Turblown.net (1Revvin7)
Turblown custom manifold w/ egt bungs in each runner, coated
Turbosmart Ext. wastegate V-band
Trublown 3.5inch Downpipe coated w/ o2 bung and egt bung.
PWR FMIC w/ mount for FC 24x3x12
$2600 for all that
Haltech e6k /w program all sensors and the extras that came with it.. 3bar map sensor, 4 wire o2
Nology coils
nology plug wires This set up is ready to go no need to splice into your existing coil wires
laptop if needed
$900
ACT extreme clutch
ACT extreme flywheel
new slave cyl w/ SS clutch line
$550
DEFI Gage setup w/ link unit II (boost, tach, oil temp, oil press, water temp, fuel press., EGT)
HKS turbo timer
$750
Sparco racing wheel w/ Works Bell quick release system
2 Sparco seats (black) with brackets 1 racing bucket, 1 rec.
$900
Tein coilovers w/ tein camber plates (front)
Adjustable rear camber links and bar from mazdatrix http://www.mazdatrix.com/h6_86-92.htm
$ 950 for everthing
T2 front and rear Calipers (new reman)w/ hawk pads
Front & rear power slot rotors
SS brake lines
$500
Fuel rails Pri and Sec of 13b-re KG parts w/-6 an fittings
x2 RC 550 inj x2 Bosche 1680 sec. inj.
SX Fuel press reg. w/ -6 fittings
Y fuel splitter w/ -6 fittings (Was running a parallel fuel setup)
$450
T2 rear Diff w/ Kazz 1.5 way lsd
$ 600
some other goodies too like body kit, core RE block, Blitz DD blowoff valve, EXt aeromotive fuel pump w/ 2 filters, Alum 10 gal fuel cell, T2 tranny, dual oil cooler setup SS lines oil filter relocation kit.
Turbonetics T04E dual BB .57 p trim w/ custom 1.0 hotside w/ heat coating by Turblown.net (1Revvin7)
Turblown custom manifold w/ egt bungs in each runner, coated
Turbosmart Ext. wastegate V-band
Trublown 3.5inch Downpipe coated w/ o2 bung and egt bung.
PWR FMIC w/ mount for FC 24x3x12
$2600 for all that
Haltech e6k /w program all sensors and the extras that came with it.. 3bar map sensor, 4 wire o2
Nology coils
nology plug wires This set up is ready to go no need to splice into your existing coil wires
laptop if needed
$900
ACT extreme clutch
ACT extreme flywheel
new slave cyl w/ SS clutch line
$550
DEFI Gage setup w/ link unit II (boost, tach, oil temp, oil press, water temp, fuel press., EGT)
HKS turbo timer
$750
Sparco racing wheel w/ Works Bell quick release system
2 Sparco seats (black) with brackets 1 racing bucket, 1 rec.
$900
Tein coilovers w/ tein camber plates (front)
Adjustable rear camber links and bar from mazdatrix http://www.mazdatrix.com/h6_86-92.htm
$ 950 for everthing
T2 front and rear Calipers (new reman)w/ hawk pads
Front & rear power slot rotors
SS brake lines
$500
Fuel rails Pri and Sec of 13b-re KG parts w/-6 an fittings
x2 RC 550 inj x2 Bosche 1680 sec. inj.
SX Fuel press reg. w/ -6 fittings
Y fuel splitter w/ -6 fittings (Was running a parallel fuel setup)
$450
T2 rear Diff w/ Kazz 1.5 way lsd
$ 600
some other goodies too like body kit, core RE block, Blitz DD blowoff valve, EXt aeromotive fuel pump w/ 2 filters, Alum 10 gal fuel cell, T2 tranny, dual oil cooler setup SS lines oil filter relocation kit.
