Crain Hi6 Install Question
02-04-2004, 10:21 PM
#12
Senior Member
Thread Starter
Join Date: Jun 2002
Location: La Plata, Maryland
Posts: 9,725
I mounted this up today. Soildered the power and ground wires up, but after getting into it further I still am not positive which set of wires out of the crain go to the ignitor side.
I have two pairs of wires coming out of the crain.
Its one of the two and the other will connect to the coil side.
Just wish I could find someone who could tell me which color wires go the ignitor side.
The directions above are vague on that pretty important detail
I have two pairs of wires coming out of the crain.
Its one of the two and the other will connect to the coil side.
Just wish I could find someone who could tell me which color wires go the ignitor side.
The directions above are vague on that pretty important detail
02-04-2004, 10:48 PM
#14
Senior Member
Thread Starter
Join Date: Jun 2002
Location: La Plata, Maryland
Posts: 9,725
Originally Posted by Cheers!' date='Feb 4 2004, 08:31 PM
i installed it in a FC, i'm not sure about FD.
BUt set the unit to run on 4 cylinder mode. You will get better performance
BUt set the unit to run on 4 cylinder mode. You will get better performance
Its not the same unfortunately.
Care to elaborate and give me some info about setting it on 4cylinder mode? Why would I see better "performance" And what better "performance" will i expect to see?
How would that be done anyway, The only adjustments on the unit are for the rev limiter...
Thanks for any info
02-04-2004, 11:06 PM
#15
Senior Member
Thread Starter
Join Date: Jun 2002
Location: La Plata, Maryland
Posts: 9,725
Derrhhh.
Sometimes my stupidity surprises even me.
It is just as it shows on Fc3s.org. I even pointed that out in my first point.
The red and white wires attch to the ignitor and the orange and black wires go to the coil.
Anyway, Cheers I would still like to hear your words about the 4cylinder option.
Sometimes my stupidity surprises even me.
It is just as it shows on Fc3s.org. I even pointed that out in my first point.
The red and white wires attch to the ignitor and the orange and black wires go to the coil.
Anyway, Cheers I would still like to hear your words about the 4cylinder option.
02-05-2004, 01:05 PM
#18
Senior Member
Thread Starter
Join Date: Jun 2002
Location: La Plata, Maryland
Posts: 9,725
Originally Posted by BoOsTin FD' date='Feb 5 2004, 07:13 AM
Here is another little pictuer that was on that document. Hope it helps.
Thanks again.
02-05-2004, 05:59 PM
#19
Senior Member
Join Date: Nov 2002
Posts: 3,108
??? by feel? i oringinally wired it up as 8 cylinder mode. Then someone told me about 4 cylinder mode and i ahve it a shot. I knew rotaries work like 4 cylinder engines. I think it has to do with how often the crane box discharges a spark.
I think the blue wire gets switched 12V. I can't remember exactly. REad the instructions
I think the blue wire gets switched 12V. I can't remember exactly. REad the instructions
02-05-2004, 07:02 PM
#20
Senior Member
Thread Starter
Join Date: Jun 2002
Location: La Plata, Maryland
Posts: 9,725
Originally Posted by Cheers!' date='Feb 5 2004, 03:59 PM
??? by feel? i oringinally wired it up as 8 cylinder mode. Then someone told me about 4 cylinder mode and i ahve it a shot. I knew rotaries work like 4 cylinder engines. I think it has to do with how often the crane box discharges a spark.
I think the blue wire gets switched 12V. I can't remember exactly. REad the instructions
I think the blue wire gets switched 12V. I can't remember exactly. REad the instructions