Series 4 Or 5?
#13
Originally Posted by TLT' date='Jun 25 2004, 06:21 PM
DANG!!!! Two fer two.....mine's a Series 5 as well....thanks for all the lineage info! Now to figure out just how much/what type porting this TII needs to be done to match a large turbo making 400-500HP@7,000RPM!
#14
The plane is essentially built, including the fuselage, and an 8.5G test wing. Getting the right engine config, and mounting it amidships directly on CG without interfering with the retractable tandem main gear is the current sticking problem. And yes, since this aircraft is the first of it's kind in the world, and it is the most recognizable Sci-Fi bird out there(latest polls show!), It's sure to get heavy worldwide attention. I already have a test-pilot, and my entire Experimental Aviation group, the 43rd, is completely behind me. It's really a shame I don't have a engine sponsor like Racing Beat......this plane is gonna rock. One of the versions of her just pulled 420MPH in the sim with a setup emulating using their 900HP 3 rotor. That was in the e-mail I sent to Mederer, but I never heard back.....FLOL! I know that usually sponsors come a'calling after the fact, but it sure would be smart of some engine-builder to step up to the plate ahead of next years' first flight. By the way....any hints on how to make a dry-sump version of this engine?
#15
Originally Posted by TLT' date='Jun 25 2004, 07:04 PM
The plane is essentially built, including the fuselage, and an 8.5G test wing. Getting the right engine config, and mounting it amidships directly on CG without interfering with the retractable tandem main gear is the current sticking problem. And yes, since this aircraft is the first of it's kind in the world, and it is the most recognizable Sci-Fi bird out there(latest polls show!), It's sure to get heavy worldwide attention. I already have a test-pilot, and my entire Experimental Aviation group, the 43rd, is completely behind me. It's really a shame I don't have a engine sponsor like Racing Beat......this plane is gonna rock. One of the versions of her just pulled 420MPH in the sim with a setup emulating using their 900HP 3 rotor. That was in the e-mail I sent to Mederer, but I never heard back.....FLOL! I know that usually sponsors come a'calling after the fact, but it sure would be smart of some engine-builder to step up to the plate ahead of next years' first flight. By the way....any hints on how to make a dry-sump version of this engine?
Technically, the stock setup is nearly a dry sump with the sump tank mounted to the bottom of the engine.
Racing Beat isnt very likely to support your project. It doesnt suprise me one bit you havent heard back, and I wouldnt expect to. They make great products, but theyre not out looking for a lot more exposure. And quite honestly, they arent exactly helpful when you do manage to get replies from them. A series of emails I had with Jim Mederer left a bad taste in my mouth...
#16
Yea, I kinda figured. That's why I'm coming to places like this where the rubber meets the road. I know in my heart I'm going to have to make this happen on my own, despite the cost, but that's also why I'm so redudndant in my posts.....I need to get this right the first time! It's good to hear that a dry sump system can be done like that because I plan on using a flat plate support mount......it'll sit directly on top of the main frame rails, and accordingly to my old man, the machinist, I should be able to make a sliding rail system to pull the unit out through the ***-end of the bird from it's mid-engine position for R&R, ect.
PS: You mark my words......RB & whoever else is sitting on their thumbs is really gonna be kickin' themselves when some rotary-house takes up the banner of aviation engines. Atkins & Powersports are just too caught up in makin' the big bucks right now to corner the upcoming market.....it'll probably be some no-name shop that sees the light, and ends up owning the aviation rotary engine market.....FLOL!
PS: You mark my words......RB & whoever else is sitting on their thumbs is really gonna be kickin' themselves when some rotary-house takes up the banner of aviation engines. Atkins & Powersports are just too caught up in makin' the big bucks right now to corner the upcoming market.....it'll probably be some no-name shop that sees the light, and ends up owning the aviation rotary engine market.....FLOL!
Thread
Thread Starter
Forum
Replies
Last Post
MAZDAROTARYPOWER
2nd Generation Specific
17
12-08-2005 02:34 PM
SPD Racing FC
RX-7 & RX-8 Parts For Sale & Wanted
15
12-03-2003 07:49 PM
rmphillip
2nd Generation Specific
5
05-11-2003 02:47 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)