Picking Up 13B-RE
#1
I bought a 13B-RE and i am picking it up tomorrow I need help with the following.
How could I check the motor to see if has any compression out of the car?
What can i do to lubricate the inside of the engine before an initial start up.
If i have to rebuild are S5 or S6 housings and rebuild kits interchangable?
I got a GT40R turbo for next to free this should give me some nice numbers but what i would like to know if it is a to4 flange or what?
How could I check the motor to see if has any compression out of the car?
What can i do to lubricate the inside of the engine before an initial start up.
If i have to rebuild are S5 or S6 housings and rebuild kits interchangable?
I got a GT40R turbo for next to free this should give me some nice numbers but what i would like to know if it is a to4 flange or what?
#2
ok add some details would you...like are you planning on using the omp? getting block off plates etc...are you going to have it rebuildt?..I'd remove water pump and inspect..replace with new one..fc or fd one fits. turbo manifolds from fd or fc will fit but depending on which one HKS tubular will not fit in FC frame. What are you going to use for ign..FC T2 coils will work well. ECU you will be using..s5 will run the RE but not to its potential..remember the RE ports are huge (think FD with large street port) Also flywheel..You must use the stock counter weight that is on the RE engine.
As for lubing engine..easy fill oil filter with oil fill engine with oil, fill lines to oil cooler with oil..crank over using air tool to prime the oil pump and get oil throught the system. Crack lines to watch oil flow to make sure that its making its way through system.. crack enough to get a small drip. easy referance...T4 flange is about the size of a pack of smokes.
As for lubing engine..easy fill oil filter with oil fill engine with oil, fill lines to oil cooler with oil..crank over using air tool to prime the oil pump and get oil throught the system. Crack lines to watch oil flow to make sure that its making its way through system.. crack enough to get a small drip. easy referance...T4 flange is about the size of a pack of smokes.
#3
Sorry for my crude questions. This is what i have
86 FC
13B-RE motor
Microtech LT-10s
Greddy FMIC
Greddy Profec B
4 Trailing Coils
S5 Flywheel
Centerforce Dual friction Clucth
And as far as lubrication i did not mean the oil system i meant the rotors do i use ATF or MMO to pre lube the engine internals. I am going to run premix to simplify things and block off plates I already have.
And about the rebuild I want to install it as is and just fire her up to get an idea of the motors condition for warranty reasons if the motor is junk im gonna use the warranty to hopefully get a running motor that will be rebuildable one not like one my friend bought that was complete trash
86 FC
13B-RE motor
Microtech LT-10s
Greddy FMIC
Greddy Profec B
4 Trailing Coils
S5 Flywheel
Centerforce Dual friction Clucth
And as far as lubrication i did not mean the oil system i meant the rotors do i use ATF or MMO to pre lube the engine internals. I am going to run premix to simplify things and block off plates I already have.
And about the rebuild I want to install it as is and just fire her up to get an idea of the motors condition for warranty reasons if the motor is junk im gonna use the warranty to hopefully get a running motor that will be rebuildable one not like one my friend bought that was complete trash
#8
well 1 revvin 7you won i got the motor in started to remove the turbo and manifold when the turbo came loose a little water came out between the turbo and manifold and when i took it off the manifold was full of water. continued to take off the turbo manifold and the rotor housings where full of water also. Just my luck $1600 for a submerged motor LOL im in the process of sending it back now but leaves me out $240 in shipping costs.
#10
if u need a manafold i have an HKS mani for sale!! has a ext. wastegate tube welded on and a ebay wastegate on the end of it, ill let it go cheap as i got it with my motor and idont need it!!! u can toss the w/g if u want too, im just to lazy to take it off cause i dont want it!! lol but yeah, pm me if interested!! i am motivated to sell!!!