2nd Generation Specific 1986-1992 Discussion

NA

Thread Tools
 
Search this Thread
 
Old 05-20-2006, 08:31 PM
  #1  
Junior Member
Thread Starter
 
simplybebop's Avatar
 
Join Date: May 2006
Posts: 18
Default

what would u guys recomend for making more power in a NA 13b. I wanna do a carb kit i know to make my swap easier. I also have to rebuild the engine so i might be able to do internals when i do that. Also how much hp does the na 13b make.
simplybebop is offline  
Old 05-20-2006, 08:38 PM
  #2  
Senior Member
 
BigTurbo74's Avatar
 
Join Date: Jul 2002
Posts: 2,315
Default

standalone and nitrous. series 4 n/a makes 146 bhp or something, and series 5 makes around 160 i think?
BigTurbo74 is offline  
Old 05-20-2006, 08:47 PM
  #3  
Junior Member
Thread Starter
 
simplybebop's Avatar
 
Join Date: May 2006
Posts: 18
Default

i wanna go carb so that standalone wont work, this motor in going in a drift car so nitrous wont work, u think na will take just a few pounds of boost???
simplybebop is offline  
Old 05-20-2006, 08:53 PM
  #4  
Senior Member
 
NotalesS's Avatar
 
Join Date: Feb 2006
Location: MENLO MAZDA
Posts: 192
Default

weld 6 ports closed, s4 rotars so theres higher compression, do LOTS of trany work. Get the miata gears so you have more brader power band. SUPER ULTRA lite flywheel. LSD. DONE



You don't need much power for a drift car. Just make sure power to waight ratio balenced.
NotalesS is offline  
Old 05-20-2006, 09:19 PM
  #5  
Junior Member
Thread Starter
 
simplybebop's Avatar
 
Join Date: May 2006
Posts: 18
Default

know of a good high performance carb kit?????
simplybebop is offline  
Old 05-20-2006, 10:15 PM
  #6  
Junior Member
 
rabius's Avatar
 
Join Date: May 2006
Posts: 29
Default

weld 6 ports closed??

S4 rotors are higher compression than what?

super lightweight flywheel will kill the rotating enertia will make breaking traction more difficult (no clutch kicks..).. maybe a midweight flywheel will work. and yes, definitely an LSD.
rabius is offline  
Old 05-21-2006, 06:02 AM
  #7  
Senior Member
 
sen2two's Avatar
 
Join Date: Feb 2005
Location: Kissimmee FL.
Posts: 1,579
Default

street port, good carb, (well tuned), S5 rotors, 200+ easy....



S4 Rotars...9.4 comp.



S5 Rotars...9.7 comp.
sen2two is offline  
Old 05-21-2006, 10:28 AM
  #8  
Senior Member
 
BigTurbo74's Avatar
 
Join Date: Jul 2002
Posts: 2,315
Default

look at the dyno sheet section of this site. look at some setups people are using and how they are working.
BigTurbo74 is offline  
Old 05-21-2006, 12:28 PM
  #9  
Junior Member
Thread Starter
 
simplybebop's Avatar
 
Join Date: May 2006
Posts: 18
Default

one more very technical question, on the front side of the accentric shaft, what size is the fitting of the hole in the end of it where the harmonic goes
simplybebop is offline  
Old 05-21-2006, 07:40 PM
  #10  
Senior Member
 
KompressorLOgic's Avatar
 
Join Date: Oct 2003
Location: WA, Renton
Posts: 714
Default

you will only make more hp than stock if your carb setup is tuned reallly well.



ive seen alot of guys with carbs actually make less hp than stock EFI with same mods.
KompressorLOgic is offline  



All times are GMT -5. The time now is 09:48 AM.