2nd Generation Specific 1986-1992 Discussion

NA

Thread Tools
 
Search this Thread
 
Old May 20, 2006 | 08:31 PM
  #1  
simplybebop's Avatar
Thread Starter
Junior Member
 
Joined: May 2006
Posts: 18
Default

what would u guys recomend for making more power in a NA 13b. I wanna do a carb kit i know to make my swap easier. I also have to rebuild the engine so i might be able to do internals when i do that. Also how much hp does the na 13b make.
Old May 20, 2006 | 08:38 PM
  #2  
BigTurbo74's Avatar
Senior Member
 
Joined: Jul 2002
Posts: 2,315
Default

standalone and nitrous. series 4 n/a makes 146 bhp or something, and series 5 makes around 160 i think?
Old May 20, 2006 | 08:47 PM
  #3  
simplybebop's Avatar
Thread Starter
Junior Member
 
Joined: May 2006
Posts: 18
Default

i wanna go carb so that standalone wont work, this motor in going in a drift car so nitrous wont work, u think na will take just a few pounds of boost???
Old May 20, 2006 | 08:53 PM
  #4  
NotalesS's Avatar
Senior Member
 
Joined: Feb 2006
Posts: 192
From: MENLO MAZDA
Default

weld 6 ports closed, s4 rotars so theres higher compression, do LOTS of trany work. Get the miata gears so you have more brader power band. SUPER ULTRA lite flywheel. LSD. DONE



You don't need much power for a drift car. Just make sure power to waight ratio balenced.
Old May 20, 2006 | 09:19 PM
  #5  
simplybebop's Avatar
Thread Starter
Junior Member
 
Joined: May 2006
Posts: 18
Default

know of a good high performance carb kit?????
Old May 20, 2006 | 10:15 PM
  #6  
rabius's Avatar
Junior Member
 
Joined: May 2006
Posts: 29
Default

weld 6 ports closed??

S4 rotors are higher compression than what?

super lightweight flywheel will kill the rotating enertia will make breaking traction more difficult (no clutch kicks..).. maybe a midweight flywheel will work. and yes, definitely an LSD.
Old May 21, 2006 | 06:02 AM
  #7  
sen2two's Avatar
Senior Member
 
Joined: Feb 2005
Posts: 1,579
From: Kissimmee FL.
Default

street port, good carb, (well tuned), S5 rotors, 200+ easy....



S4 Rotars...9.4 comp.



S5 Rotars...9.7 comp.
Old May 21, 2006 | 10:28 AM
  #8  
BigTurbo74's Avatar
Senior Member
 
Joined: Jul 2002
Posts: 2,315
Default

look at the dyno sheet section of this site. look at some setups people are using and how they are working.
Old May 21, 2006 | 12:28 PM
  #9  
simplybebop's Avatar
Thread Starter
Junior Member
 
Joined: May 2006
Posts: 18
Default

one more very technical question, on the front side of the accentric shaft, what size is the fitting of the hole in the end of it where the harmonic goes
Old May 21, 2006 | 07:40 PM
  #10  
KompressorLOgic's Avatar
Senior Member
 
Joined: Oct 2003
Posts: 714
From: WA, Renton
Default

you will only make more hp than stock if your carb setup is tuned reallly well.



ive seen alot of guys with carbs actually make less hp than stock EFI with same mods.



All times are GMT -5. The time now is 01:13 AM.