2nd Generation Specific 1986-1992 Discussion

hesistation at 4000 rpms

Thread Tools
 
Search this Thread
 
Old 10-30-2002, 02:11 AM
  #21  
Senior Member
 
Dragon's Avatar
 
Join Date: Sep 2002
Posts: 2,550
Default

Originally Posted by mazdaspeed101' date='Oct 29 2002, 09:19 PM
i think i might have an intake leak or a bad vacuum line because i can hear air when the engine is running i think i might have might have a bad intake manifold gasket. would that effect anything
Umm yes, but mostly at idol and low rpms... It shouldn't make much diffrence in the 3800 rpm up range...



you may want to change your fuel filter, but more than likely your going to have to get dirty and rip the upper intake manifold etc off to fix your problem..
Dragon is offline  
Old 10-30-2002, 06:56 PM
  #22  
Senior Member
Thread Starter
 
mazdaspeed101's Avatar
 
Join Date: Jun 2002
Location: Kunsan AB, Korea (used to be vegas!)
Posts: 263
Default

yeah i am going to have to replace the fuel filter i havent done that since i had the car and is hard to take off the intake manifold on a t2. i noticed though at idle my car dont stay at a set rpm and it usually dies if i dont warm it up
mazdaspeed101 is offline  
Old 10-30-2002, 07:38 PM
  #23  
Senior Member
 
RX7Aggie's Avatar
 
Join Date: Apr 2002
Location: NASA/JSC - Clear Lake, TX
Posts: 870
Default

welcome to the world of old cars. if its not one thing, it another. as much as i love fixing stuff on my car, i hate diagnosing the problem. tell me what's wrong, and i can fix it. figuring out what's wrong, that's the hard and fustrating part, especially when this is my daily driver.



an again, i have somehow managed not to study for my poli sci test. no surprise there.
RX7Aggie is offline  
Old 10-31-2002, 04:05 PM
  #24  
Senior Member
 
RXheaven13b's Avatar
 
Join Date: Dec 2001
Location: Jacksonville, FL
Posts: 324
Default

If it still dose it make sure you're 6 port actuators are working rite. around 4k they open up like a 4 barrle carb, some times they stick and don't open causing the lag you're getting.
RXheaven13b is offline  
Old 10-31-2002, 07:04 PM
  #25  
Senior Member
Thread Starter
 
mazdaspeed101's Avatar
 
Join Date: Jun 2002
Location: Kunsan AB, Korea (used to be vegas!)
Posts: 263
Default

is there a way to fix the ports so they dont get stuck or do they have to be replaced
mazdaspeed101 is offline  
Old 11-01-2002, 11:40 AM
  #26  
Senior Member
 
ChainSawOnSteroids's Avatar
 
Join Date: Jul 2002
Posts: 1,007
Default

wire open your 5 and 6 ports, its in the faq sectio, but in any case, they are under you IAC VALVE, open them and put some twistie ties, hope this helps, if not USE THE FOKIN SAEARCH BUTTON! kidding, lol its defenately in the FAQ section, after i wired mine open, car keeps pulling after 4k hard, no hesitaion no slow after 6k i like it, and who cares about low end? if you want low end get a 5.slow
ChainSawOnSteroids is offline  
Old 11-01-2002, 07:10 PM
  #27  
Senior Member
Thread Starter
 
mazdaspeed101's Avatar
 
Join Date: Jun 2002
Location: Kunsan AB, Korea (used to be vegas!)
Posts: 263
Default

is it an easy job or is there alot of stuff to take off
mazdaspeed101 is offline  
Old 11-01-2002, 07:26 PM
  #28  
Senior Member
Thread Starter
 
mazdaspeed101's Avatar
 
Join Date: Jun 2002
Location: Kunsan AB, Korea (used to be vegas!)
Posts: 263
Default

i stuck fuel injector cleaner in my car because i havent done it in awhile and i didnt have the hesitation for a whole day and a half and then today when i was going to work it started doing it again and i thought that was the problem. I have new injectors
mazdaspeed101 is offline  
Old 11-01-2002, 07:27 PM
  #29  
Senior Member
Thread Starter
 
mazdaspeed101's Avatar
 
Join Date: Jun 2002
Location: Kunsan AB, Korea (used to be vegas!)
Posts: 263
Default

would it matter if i stuck more injector cleaner in
mazdaspeed101 is offline  
Old 11-01-2002, 07:53 PM
  #30  
Super Moderator
 
vosko's Avatar
 
Join Date: Jul 2001
Location: NJ
Posts: 17,839
Default

maybe you got a faulty injector or clogged fuel filter ?
vosko is offline  


Quick Reply: hesistation at 4000 rpms



All times are GMT -5. The time now is 06:36 PM.