2nd Generation Specific 1986-1992 Discussion

a few quick questions

Thread Tools
 
Search this Thread
 
Old 02-21-2009, 11:04 AM
  #1  
Member
Thread Starter
 
thecrow's Avatar
 
Join Date: Jan 2009
Posts: 35
Default

1. The car will rev when sitting still up to high rpms. but when im driving it and i get on it in first. itll go to around 3 grand. then i can sill push it but it sounds nuts then backfires. any suggestions how to fix that?



i also am running an open exhaust manifold. i know my ports arnt actuating but i didnt think that would make my car do that. and all emissons are removed along with tb mod.



2. i am leaking oil from the oil filter side of the engine. im thinking it might be coming from the o rings on the filter stand but is there any other common place for it to come from on that side?



3. my oil smells like gas. i heard it was common but id rather be safe than sorry. is this a big deal?



thanks for the help
thecrow is offline  
Old 02-21-2009, 11:28 AM
  #2  
Super Moderator
 
1988RedT2's Avatar
 
Join Date: Apr 2002
Location: VA
Posts: 2,532
Default

My oil leak was from the filter pedestal o-rings. A bit of a pain getting a 10mm wrench on the nuts to remove it, but not too bad.



Gas isn't doing your oil any good. I change mine frequently.



So, under load the engine misfires around 3 grand? Could be inadequate fuel or weak ignition. Try new plugs. Wires okay? Could be "3800 RPM hesitation"? Check grounds.



Good luck!
1988RedT2 is offline  
Old 02-21-2009, 12:34 PM
  #3  
Member
Thread Starter
 
thecrow's Avatar
 
Join Date: Jan 2009
Posts: 35
Default

wires are newer and plugs are brand new.

all my grounds seem good. i redid them when i put my motor in.

i'm just getting a little frustrated. because you can take it past 3800 to past 4500 but the motor sounds nuts then when you let off it gives a good backfire. it looses most power right around 3000
thecrow is offline  
Old 02-21-2009, 06:28 PM
  #4  
Senior Member
 
RONIN FC's Avatar
 
Join Date: Oct 2003
Location: Boston Ma.
Posts: 1,420
Default

I suspect it may have something to do with your TB mod.
RONIN FC is offline  
Old 02-21-2009, 09:03 PM
  #5  
Member
Thread Starter
 
thecrow's Avatar
 
Join Date: Jan 2009
Posts: 35
Default

why would the t/b mod make it do that?
thecrow is offline  
Old 02-22-2009, 08:46 AM
  #6  
Super Moderator
 
1988RedT2's Avatar
 
Join Date: Apr 2002
Location: VA
Posts: 2,532
Default

A little history is always helpful. Did it always have the problem, or did it start doing it right after you did some work on it?
1988RedT2 is offline  
Old 02-22-2009, 11:07 AM
  #7  
Member
Thread Starter
 
thecrow's Avatar
 
Join Date: Jan 2009
Posts: 35
Default

i put the used "new" motor in with around 60k on it. and yes, it has always done it since i put the motor in. i dont daily the car so in the few times that i have driven it, it has done that.



keep in mind that i have the stock manifold on with no exhaust hooked up. im assuming that backpressure would help the motor.



the problem only happens under load. revs nice while sitting.



good cold idle. stutters a bit when the t stat is opening then clears right up and idles fine again.
thecrow is offline  
Old 02-22-2009, 06:34 PM
  #8  
Junior Member
 
varianfc3s's Avatar
 
Join Date: May 2007
Location: New Mexico
Posts: 11
Default

Put the exhaust back on, you need back pressure
varianfc3s is offline  
Old 02-22-2009, 07:58 PM
  #9  
Senior Member
 
Nateb123's Avatar
 
Join Date: Jan 2008
Location: Vancouver, BC
Posts: 143
Default

Yeah, no backpressure means your aux ports are staying closed. They normally open at 3800rpm, and if they're slow due to bad grounding you get hesitation. However, not having them open at all (since no exhaust means no backpressure) means you get fine performance until you hit the time they should be opening. Then it runs rich, has crappy hp, etc etc.
Nateb123 is offline  
Old 02-22-2009, 11:58 PM
  #10  
Senior Member
 
fc3s4utnv's Avatar
 
Join Date: Jan 2005
Location: Greenwood AR
Posts: 831
Default

Originally Posted by 1988RedT2' post='917171' date='Feb 21 2009, 11:28 AM
My oil leak was from the filter pedestal o-rings. A bit of a pain getting a 10mm wrench on the nuts to remove it, but not too bad.



Gas isn't doing your oil any good. I change mine frequently.



So, under load the engine misfires around 3 grand? Could be inadequate fuel or weak ignition. Try new plugs. Wires okay? Could be "3800 RPM hesitation"? Check grounds.



Good luck!
Its easier to jack the car up get a long extension and a swivel... takes alot less time.
fc3s4utnv is offline  


Quick Reply: a few quick questions



All times are GMT -5. The time now is 02:26 AM.