Fuel Injection Conversion
02-01-2004, 08:34 PM
#21
Junior Member
Thread Starter
Join Date: Jan 2004
Location: Sydney Australia
Posts: 29
if his was a turbo engine it should have em. theyre prob blocked off with a fuel injection plug kit
theres a slight coolant o ring incompatibility issue with pre FC engines and FC engines.
theres a slight coolant o ring incompatibility issue with pre FC engines and FC engines.
This kit from Racing Beat says it's for 6 port engines. Mine's 4 port. Anyway, can't see anything like it on the block.
I'll fire up the digital camera shortly & get some close-up photos.
Amanda
02-01-2004, 09:18 PM
#22
Junior Member
Thread Starter
Join Date: Jan 2004
Location: Sydney Australia
Posts: 29
Just found this in another thread.
http://www.mazdacomp.com/fuelinjection.jpg
My existing setup appears to have a 3/4" thick plate between the manifold & the block. Me thinks I could replace that with one of these, and use my existing carby as the throttle body.
Amanda
http://www.mazdacomp.com/fuelinjection.jpg
My existing setup appears to have a 3/4" thick plate between the manifold & the block. Me thinks I could replace that with one of these, and use my existing carby as the throttle body.
Amanda
02-02-2004, 03:31 PM
#23
to infinity & beyond, me
Join Date: Aug 2001
Location: santurce
Posts: 5,124
if my car wasnt covered in snow/ice id take some pics....if your 13b was from the 70s, it was carbed, it wouldnt have the fuel injector plugs, it would be a 4 port and i believe it would say mazda on the rotor housings. if it came out of a car from the 80s, it was fuel injected, either 6(NA) or 4 port(turbo).
that fuel rail looks pretty good. just make sure that it fits the LIM bolt pattern.
that fuel rail looks pretty good. just make sure that it fits the LIM bolt pattern.
02-03-2004, 08:19 AM
#25
Senior Member
Join Date: Jan 2003
Location: London, Ontario
Posts: 2,871
Originally Posted by commanda' date='Jan 16 2004, 04:04 PM
I have an Australian 1982 RX7 (SA22C6.......). The original 12A has been ditched in favour of a 13B, one of the cheap turbo imports. It has never had the turbo fitted since I've had it, just the 4 barrel Nikki. The motor has been rebuilt, 2 years ago, with high compression rotors and a mild port job done.
Now I want to ditch the carb, and go with fuel injection, with an aftermarket ECU. I'm an electronics engineer, soI'll probably build a megasquirtAVR to run it.
I spoke to my local wrecker about getting an EFI inlet manifold, but was told the primary injectors are actually in the block, so it won't work.
Can anybody offer any suggestions on where to go from here.
Thanks inAdvance.
Amanda
Now I want to ditch the carb, and go with fuel injection, with an aftermarket ECU. I'm an electronics engineer, soI'll probably build a megasquirtAVR to run it.
I spoke to my local wrecker about getting an EFI inlet manifold, but was told the primary injectors are actually in the block, so it won't work.
Can anybody offer any suggestions on where to go from here.
Thanks inAdvance.
Amanda
I'd like to see one with one of these from a Mustang on it.
BBK Mustang Throttle Body
Or these from a Camaro. Should be easier to split airflow front / rear.
LT1 Throttle Body
02-03-2004, 11:40 AM
#27
to infinity & beyond, me
Join Date: Aug 2001
Location: santurce
Posts: 5,124
u know after i posted about that i was trying to figure out what exactly the difference was...im still looking for old school housing pics to post up.
but if i rememeber correctly, the MAZDA size and font style is larger about 3/4 to 1" in size as opposed to the newer bout 1/2" size. as soon as i find some pics ill post them...
but if i rememeber correctly, the MAZDA size and font style is larger about 3/4 to 1" in size as opposed to the newer bout 1/2" size. as soon as i find some pics ill post them...
02-04-2004, 11:37 AM
#28
Member
Join Date: Jan 2004
Location: Richmond, KY
Posts: 30
Finally, I found some pics!
http://www.rotaryresponse.com/ebay/MVC-475Fopt.jpg
From: http://rxforyour7.com/mazda%20rotary.htm
The later housings will say MAZDA and 13b (or 12a, depending..) on them as well...
http://www.rotaryresponse.com/ebay/MVC-475Fopt.jpg
From: http://rxforyour7.com/mazda%20rotary.htm
The later housings will say MAZDA and 13b (or 12a, depending..) on them as well...
02-05-2004, 12:35 AM
#30
Junior Member
Thread Starter
Join Date: Jan 2004
Location: Sydney Australia
Posts: 29
can anyone tell me what the downdraft efi thing on the first page of this thread is? like what is it, who has it? thanks.
They're made by tweakit. The agent here in Australia puts them up on ebay.com.au. I think it's AUS $854 and a manifold to suit another AUS $250. Then you need to buy the actual injectors themselves.
http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...&category=32624