1st Generation Specific 1979-1985 Discussion

Best Place To Get A Carb Rebuild Kit?

Old Aug 12, 2003 | 01:30 AM
  #1  
ZenRXSeven's Avatar
Thread Starter
Senior Member
 
Joined: Jul 2003
Posts: 248
From: Pottstown, PA
Default

Well, I gotta rebuild the carb on the '85 S... (same car I was asking about in the "Newly Purchased Car Won't Start Thread," but I didn't feel like ressurecting that thread), 'cause it is one fantastical mess in there. The jets were completely gummed up, and the gaskets were worn to hell as well. Anyway, where's the best (read: cheapest) place to get a carb rebuild kit? I checked out Mazdatrix and they sell one for like $75 or so, which isn't so bad, I guess. Also, does anyone know if the Mazdatrix kit comes with the two little fuel inlet screens or not? They sell them seperately, so I wasn't sure if they came in the kit or not. Thanks!
Old Aug 12, 2003 | 08:42 AM
  #2  
lxk199's Avatar
Senior Member
 
Joined: Nov 2002
Posts: 278
From: Pennsylvania
Default

Jeez you just can't stop yappin, can ya? yap yap yap yap yap goes the ZenRX ...lol...anyways, I'd check out local auto parts stores as well on the rebuild kits, that's where I got the one for my SE, although that was a Holley carb, not a Nikki or whatever the hell came on the stock RX-7's...
Old Aug 12, 2003 | 07:29 PM
  #3  
ZenRXSeven's Avatar
Thread Starter
Senior Member
 
Joined: Jul 2003
Posts: 248
From: Pottstown, PA
Default

Yeah, I got one from Napa, for like $40 or so. Not too shabby. Anyway, as an update to the project, I drained the gas tank.... like 8 gallons of putrid orangish-brown rotten gasoline. Yippie. Now, how do I dispose of this without setting it on fire on my driveway/street/neighbor's front lawn?



Then I pulled the tank off to get a peak inside, and it looks nice and clean. No rust whatsoever. Yippie! There's some miscellaneous unidentifiable particles sittin' around in there though, so I wanna flush the tank, but I'm not sure what's the best way to go about doing that. Anybody got any ideas? Oh, and I need to replace the connectors for the fuel level sender wires. They're nice and corroded.



The tank is super rusty on the outside though, so I figure I'll just sand away at it and then coat it with a rust-proof primer or something. How's that sound?
Old Aug 12, 2003 | 08:07 PM
  #4  
HotPilot's Avatar
Member
 
Joined: Dec 2002
Posts: 41
From: C'burg,OH
Default

hey there.. most radiator repair shops have a big tank that they use to boil out radiators... at least the one in my hick town in Ohio does.. so anyways you should be able to get it done and even have them test it for a pinhole leaks and such.. good luck
Old Aug 12, 2003 | 11:52 PM
  #5  
ZenRXSeven's Avatar
Thread Starter
Senior Member
 
Joined: Jul 2003
Posts: 248
From: Pottstown, PA
Default

Sweet, I did not think of that. Thanks a bunch.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Spidey
2nd Generation Specific
3
Sep 25, 2003 10:46 PM
rotarypower101
ECU Discussions
4
Aug 11, 2003 09:55 PM
WishIhadaRX7
Rotary Engine Building, Porting & Swaps
11
Aug 1, 2003 10:39 AM
JaySpec7
3rd Generation Specific
5
Jun 18, 2003 01:30 PM
9BASE3
3rd Generation Specific
6
Mar 6, 2003 11:30 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Thread Tools
Search this Thread

All times are GMT -5. The time now is 01:30 PM.