1st Generation Specific 1979-1985 Discussion

86 6-port Problems

Old Sep 6, 2003 | 11:20 PM
  #1  
Red12aRx7's Avatar
Thread Starter
Senior Member
 
Joined: Jul 2002
Posts: 233
From: Carlisle PA
Default

I just put in my 6-port with holley carb and intake, headers and all the stuff I had on my car before. It starts up and idles ok, then if has absolutley no throttle response, if you smash it, it just climbs like you are barely touching it. And it can't even make it up a hill to get into my garage after I backed it out to get the antifreeze right. It just dies on me. I didn't have the fuel pump in yet, yea I know i need the damn fuel pump in, but shouldn't it still have enough power to get it atleast into my garage, or atleast have some response? Could it be ignition, but I have spark to my plugs and my coils are ok.
Old Sep 6, 2003 | 11:49 PM
  #2  
Smog Fighter's Avatar
Senior Member
 
Joined: Nov 2002
Posts: 569
From: Bakersfield, California
Default

Check timing. sounds like you have it retarded.
Old Sep 7, 2003 | 02:10 AM
  #3  
Racer X's Avatar
Senior Member
 
Joined: Sep 2002
Posts: 5,542
From: Vanderhoof,BC(Canada)
Default

Glad to hear it runs at least.I hope I was some help to you.Raul is right tho.I think you need to time you motor.And might as well test the compression to see what the engine is like inside.
Old Sep 7, 2003 | 09:18 AM
  #4  
nod1stgen's Avatar
Senior Member
 
Joined: Aug 2003
Posts: 249
From: panama city, florida
Default

Are you sure the linkage is hooked up right?

And also check your Accelerator pump adjustment.
Old Sep 7, 2003 | 09:31 AM
  #5  
Red12aRx7's Avatar
Thread Starter
Senior Member
 
Joined: Jul 2002
Posts: 233
From: Carlisle PA
Default

We checked the compression it is fine. We are looking at a messed up coil right now. My trailing coil always reads 2.4 on any coil we put on it. and on my leading they are all 1.4 were they are supposed to be. What is the deal with that. And I am pretty sure that the timing is right, we took it out top dead center, and pulled my other one off my 12a at top dead center so it should've been close.
Old Sep 7, 2003 | 10:00 PM
  #6  
Red12aRx7's Avatar
Thread Starter
Senior Member
 
Joined: Jul 2002
Posts: 233
From: Carlisle PA
Default

It runs, the timing was off and I had to replace the plugs, distributor and rotor. Its still a little rich, but we are working that out. But now I have no guage bezel lights, rear lights or just about anythign else elctronical? what could be the problem. All of the fuses check out except for the one that is called opener. And it blows everytime I turn my headlights on. My headlights are the only thing that work.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Silver7
Rotary Engine Building, Porting & Swaps
4
May 4, 2008 07:27 PM
TweakGames
Rotary Engine Building, Porting & Swaps
25
Oct 14, 2007 12:10 AM
Infinite
2nd Generation Specific
8
Jun 3, 2005 02:40 PM
Bebirasta
Rotary Engine Building, Porting & Swaps
12
Jul 27, 2003 05:46 PM
The Blue Bomber
2nd Generation Specific
8
Oct 31, 2002 04:08 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Thread Tools
Search this Thread

All times are GMT -5. The time now is 06:08 PM.