List To Get It Running..
#1
Ok.. Details on the truck are as follows..
..New Universal 18 circuit "Painless wiring" wiring harness..
..Rebuilt T2 engine..
..New Clutch and pressure plate..
..Stock T2 turbo
..Stock intercooler
..12a Carb
..S4 T2 tranny
..Stock repu Rear (for now mwuhahaha)
..No guages in the dash
..S4 oil cooler
Need..
..Weber side draft carb
..Fuel pump
..Fuel Pressure regulator
..Radiator
..Alternator
..fan and shroud
..J 109 coils
..Manifold for t2 to weber carb
..Block off plates for Omp and smog junk
..Boost controller, manual or Home depot style
..Down pipe
..Blow off valve
..Custom driveshaft
..Money
This is the bare bones list of what I need to get it running.. for sevenstock.. Not show worthy, but Driveable.. Maybe a New coat of Primer is needed too...
..New Universal 18 circuit "Painless wiring" wiring harness..
..Rebuilt T2 engine..
..New Clutch and pressure plate..
..Stock T2 turbo
..Stock intercooler
..12a Carb
..S4 T2 tranny
..Stock repu Rear (for now mwuhahaha)
..No guages in the dash
..S4 oil cooler
Need..
..Weber side draft carb
..Fuel pump
..Fuel Pressure regulator
..Radiator
..Alternator
..fan and shroud
..J 109 coils
..Manifold for t2 to weber carb
..Block off plates for Omp and smog junk
..Boost controller, manual or Home depot style
..Down pipe
..Blow off valve
..Custom driveshaft
..Money
This is the bare bones list of what I need to get it running.. for sevenstock.. Not show worthy, but Driveable.. Maybe a New coat of Primer is needed too...
#9
My REPU has a very heavy exhaust system consisting of six Rotary Engineering glasspacks (two longs, four shorts) and a couple of RX-7 driveshafts as pipes (full length primaries with an H connection about where RB headers would normally Y together). It's grossly overdone and quite heavy. Anyway, all that weight on my old tired motormounts was enough to allow the pan to torque down and hit the crossmember. Or maybe it was simply engine torque?
My advice is to not even bother, since it's already pretty close stock. [hint] I want you to get your truck done quickly! [/hint] I'll be cutting my exhaust in half and leaving only three glasspacks on the truck and using two or three on the GLC. I only really need one if my header collects early, as in my MG. It's only got a single long glasspack with a very short header and a Monza dual tip at the end with little glasspacks in it. It's only a little louder than my REPU, and my REPU is not all that loud.
Both exhausts were done over 10 years ago, when RE was still in business. Man, I wish I could get me some new glasspacks. Somebody out there ought to get the patent and start producing these things again. They're that good.
My advice is to not even bother, since it's already pretty close stock. [hint] I want you to get your truck done quickly! [/hint] I'll be cutting my exhaust in half and leaving only three glasspacks on the truck and using two or three on the GLC. I only really need one if my header collects early, as in my MG. It's only got a single long glasspack with a very short header and a Monza dual tip at the end with little glasspacks in it. It's only a little louder than my REPU, and my REPU is not all that loud.
Both exhausts were done over 10 years ago, when RE was still in business. Man, I wish I could get me some new glasspacks. Somebody out there ought to get the patent and start producing these things again. They're that good.
#10
The problem with my truck is that the original ngine mount crossmember was cut off by the previous owner... so since I have to make custom mounts.. I was thinking Imight as well Locate the engine in its lowest possible position..