NoPistons -Mazda Rx7 & Rx8 Rotary Forum

RX-8 Discussion Discussion on Mazda's newest rotary powered vehicle.

Working on a little project...

Thread Tools
 
Search this Thread
 
Old 06-23-2009, 11:40 PM
  #1  
Senior Member
Thread Starter
 
1Revvin7's Avatar
 
Join Date: Oct 2001
Location: Peoria, AZ
Posts: 10,906
Default
Prototyping a new turbo kit for the 8. Got a little toy for it; Precision Billet Gt35R. Car previously had the Greddy Turbo kit..
1Revvin7 is offline  
Reply
Old 06-25-2009, 05:14 AM
  #2  
Junior Member
 
diedxjustxyesterday's Avatar
 
Join Date: May 2009
Location: San Diego
Posts: 4
Default
Woo hoo! Lovin the yellow.
diedxjustxyesterday is offline  
Reply
Old 06-25-2009, 09:51 PM
  #3  
Senior Member
Thread Starter
 
1Revvin7's Avatar
 
Join Date: Oct 2001
Location: Peoria, AZ
Posts: 10,906
Default
Moving along..
1Revvin7 is offline  
Reply
Old 06-25-2009, 10:30 PM
  #4  
Senior Member
 
GreyGT-C's Avatar
 
Join Date: Mar 2003
Location: Disclaimer: posts made after 11AM are most likely alcohol induced. Please disregard unless very funn
Posts: 2,436
Default
i don't think the blue tape will hold up to the heat of a rotary's exhaust.

























j/k... looking good so far.
GreyGT-C is offline  
Reply
Old 07-15-2009, 07:51 PM
  #5  
Senior Member
Thread Starter
 
1Revvin7's Avatar
 
Join Date: Oct 2001
Location: Peoria, AZ
Posts: 10,906
Default
Tape has been replaced
1Revvin7 is offline  
Reply
Old 08-24-2009, 07:01 PM
  #6  
Senior Member
Thread Starter
 
1Revvin7's Avatar
 
Join Date: Oct 2001
Location: Peoria, AZ
Posts: 10,906
Default


1Revvin7 is offline  
Reply
Old 01-18-2010, 12:41 AM
  #7  
Senior Member
Thread Starter
 
1Revvin7's Avatar
 
Join Date: Oct 2001
Location: Peoria, AZ
Posts: 10,906
Default
Jumping back on this. Time to punch this out.



Swapped to a water cooled 60 trim T04E; .96 undivided P trim turbine



We are also working on a GTX4294R turbo kit for someone else...



Hmm... all my attachments are failing..
1Revvin7 is offline  
Reply
Old 01-18-2010, 12:57 AM
  #8  
Super Moderator
 
mazdaspeed7's Avatar
 
Join Date: Sep 2002
Location: Savannah, Ga
Posts: 2,763
Default
Nice! whats the deal with that flange? Have it milled yourself or did you chop up another(greddy?)? Looks very good either way though.
mazdaspeed7 is offline  
Reply
Old 01-18-2010, 02:27 PM
  #9  
Senior Member
Thread Starter
 
1Revvin7's Avatar
 
Join Date: Oct 2001
Location: Peoria, AZ
Posts: 10,906
Default
Its Racingbeat's flange. Very nice; as it transitions to a round hole from the square ports; but its $125..
1Revvin7 is offline  
Reply
Old 01-18-2010, 03:05 PM
  #10  
Super Moderator
 
mazdaspeed7's Avatar
 
Join Date: Sep 2002
Location: Savannah, Ga
Posts: 2,763
Default
Originally Posted by 1Revvin7
Its Racingbeat's flange. Very nice; as it transitions to a round hole from the square ports; but its $125..


Still sounds like its worth it...
mazdaspeed7 is offline  
Reply



Advanced Search
Quick Reply: Working on a little project...


Reply Closed Thread Share

All times are GMT -5. The time now is 08:25 PM.