NoPistons -Mazda Rx7 & Rx8 Rotary Forum

NoPistons -Mazda Rx7 & Rx8 Rotary Forum (https://www.nopistons.com/)
-   Rotary Engine Swaps (https://www.nopistons.com/rotary-engine-swaps-39/)
-   -   B2000 Rotary Swap need help (https://www.nopistons.com/rotary-engine-swaps-39/b2000-rotary-swap-need-help-72482/)

hawaii4113 06-04-2009 08:43 AM

Hello

I'm looking to do a 13b motor swap to my b2000 and i would like to know what i am getting in to???

Will the swap be hard or do they make motor mounts that would make it a easier swap or do i choose some thing else???? https://www.nopistons.com/forums/pub...IR#>/wacko.gif

RX200013B 06-04-2009 04:36 PM

BE ready to fab up new engine mounts, hole for the clutch cylinder at minimun. on mine, did new engine, trans mount, hole in trany tunnel, moved all fuel lines and fuel tank to the left side (because the exhaust is on the right side now) rewire for EFI, moved battery to the bed cause the airflow meter wants to be there. if you did a carb and dizzy would possibly be easier. i will try to get some pics up soon.





let us know how the project comes along!

hawaii4113 06-04-2009 08:39 PM

thanks for that



um i wanted to know if the b2200 motor mounts are the same as the b2000 i thought they were but not sure. I found a site that had the mount already made but i dont know what to do ?????



So I'm a little lost and do you have pics that I might be able to look at

mazdaspeed7 06-04-2009 11:32 PM

https://www.nopistons.com/forums/88-Mazda-B...uck-t66555.html

hawaii4113 06-05-2009 05:56 AM

was there any cutting in the fire wall for any thing and would the comos motor fit

RX200013B 06-05-2009 09:00 AM

i cant get the pics to load? having problems

RX200013B 06-05-2009 09:07 AM

http://www.rx7club.com/showthread.ph...04#post9267104





here is a thread start

mazdaspeed7 06-05-2009 04:06 PM


Originally Posted by hawaii4113' post='922460' date='Jun 5 2009, 06:56 AM
was there any cutting in the fire wall for any thing and would the comos motor fit





The cosmo block should fit fine without cutting of the firewall, but you will need to make a new brace to clear the oil pan as I did with my mounts, as well as make new mounts for the motor. My mounts will not fit the cosmo block, only 13b and 13bt engines from 2nd gen rx7's.



If theres enough interest, I could do an 13b-rew mount as well, but I have no plans of doing the 13b-re cosmo mounts.



But with any of those engines, I doubt the stock turbo(s) will clear the frame on the b series truck. You will need a custom manifold and exhaust.

RX200013B 06-05-2009 04:25 PM

I like your mount and cross bar set-up, but can't be used on a lowered truck,!

mazdaspeed7 06-06-2009 01:49 PM


Originally Posted by RX200013B' post='922492' date='Jun 5 2009, 05:25 PM
I like your mount and cross bar set-up, but can't be used on a lowered truck,!





Any higher, and the firewall has to be cut. You either have to make a new oil pan to clear a straight cross bar, or drop the cross bar to clear the pan.



I wonder if the block is strong enough to act as a stressed member?


All times are GMT -5. The time now is 04:26 AM.


© 2024 MH Sub I, LLC dba Internet Brands