OK first the run down on the car, 10th Anniversary, 47,000 miles, everything is in excellent condition. The clutch was totally fried, even fried the flywheel, which i hope can find another somewhere cheap cause the aftermarkets are a small fortune, got the clutch out the evening, the new ACT clutch should be here this week from rotormotorsports, the sunroof motor is a little tired and it needs a new door lock on the drivers side.



Now for the good stuff, looks like a few mods have been done, but I am still looking it over. It has 3 inch Racing Beat exhaust back to the Y-pipe, then goes 2.75 out the back, looks like a racing beat drop down as well, possibly a shorts shifter, can't tell but it looks it. Also a very funky guage and a funked up button from racing beat, I have included the pics. Has one dent in the door, needs paint and the 10th AE badges to be perfect, they got stolen at some point.



Here are the pics!!!



https://www.nopistons.com/images/ae1.jpghttps://www.nopistons.com/images/ae2.jpg

https://www.nopistons.com/images/ae3.jpg

https://www.nopistons.com/images/ae4.jpg

https://www.nopistons.com/images/ae5.jpg

https://www.nopistons.com/images/ae6.jpg

https://www.nopistons.com/images/ae7.jpg

https://www.nopistons.com/images/ae8.jpg

Oh yeah great another TII that I don't have! https://www.nopistons.com/forums/pub...DIR#>/wink.png



Great car! Of course I'd take a 10th AE in almost any condition if I could swing it. Something like that's worth the trouble ressurecting.

That gauge is a boost control module, controls the boost curve, I bet it has the fuel cut controller as well! That module allows fingertip control from 7-15 PSI. Part #23000 in the Racing Beat catalog ( which is a simply beautifull catalog might I add ) Sounds like the car is a great find, but its not original anymore, so Ill only offer you $500 to take it off your hands https://www.nopistons.com/forums/pub...1047683785.gif You fugger ! By the way, are there alot of TIIs for sale on the west coast? And I see the weather report for Seattle today, 55 degrees?? No wonder you dont need A/C there!!!!!

rob is correct! again congrats. you should have ALOT of fun. i have a spare 89 TII flywheel that just needs resurfacing. i know its ALOT lighter than a S4 TII flywheel. if anyone can confirm it will work. it's all yours https://www.nopistons.com/forums/pub...IR#>/smile.png

awesome, where did you find it :o

Actually sidewinderx7 found it for me! HA HA dunno what I was thinking there. LOL

It woudln't work, different counterweights between the s4 and s5.





Take the flywheel to a profesional speed/machine shop, they'll tell you if it can be recut again. Should also notice that it is a stepped flywheel. If they dont' know that, don't let them have the flywheel.





C

Well that car is in great ******* condition. I got to "drive https://www.nopistons.com/forums/pub...#>/biggrin.png " it from Everett, and it was awesome. lol, j/k.

Alright seriously the car is nice. The boost controller is a serious find, and the exhaust is like brand new.

Congrats Phinsup!

No I used to turn flywheels myself and I can promaise you this one has about 50 hot spots in it.... I don't think an respecatble machine shope would turn and it's not something I want to risk with a $400.00 clutch LOL



Soo... I either need to find a used turnable flywheel or buy a lightened for a cool $300.00+



Thanks for answering my question turbortor on the flywheels... at least I know where I am at!!

Looks pretty good man!

Good cleaning and it will look like brand new!

Flywheel



Hoping this dude still has the flyhweel.

Good luck.



Also how much did ya pay for it? lol want to sell it?? hahaha

$2,500



Isamu didn't tell you guys how much fun we had getting it home the first night LOL

lol

same amount I was selling my GT for... until that ******* with the vette had to start ****...

So who has some cool parts they want to sell to me hella cheap cause I am one poor ass fugger.

uummm.....

Got a set of seats out of an 89 LX mustang https://www.nopistons.com/forums/pub...#>/biggrin.png https://www.nopistons.com/forums/pub...>/rolleyes.gif

lol

I also have an engine driven cooling fan off of an 89 GT mustang... lol



Sorry no parts for 7's yet... though if I do run across them I will most likely pick them up incase you guys need anything..

Yea, it was quite an adventure to say the least. https://www.nopistons.com/forums/pub...#>/biggrin.png I'm just glad we didn't see any cops when we were towing it, since they probably wouldn't of liked the fact that we were towing it after sunset with no lights or anything. And to think it was all a stinking battery cable and bad fuel filter. Oh well, I must say it sounded real strong after we got it running that night! Much better than at the lot.

Yea it has turned over first try every time since.... needless to say I put it on jack stands to pull the tranny.. https://www.nopistons.com/forums/pub...DIR#>/wink.png

I think that was a good idea. We wouldn't want another mishap with the ramps. :o

https://www.nopistons.com/forums/pub...DIR#>/moon.gif -> ramps

:bigok:

I just put a generic fuel filter on it until I can order a quality one, the Fram filters suck balls. I need to get a throttle cable too, where is the best place to get that... dealer?

I would call and ask. They have throttle cables at Mazdatrix for 47.00$. I called the dealer in Lynnwood about bearings for my stationary gears and he quoted me 15.50$, plus he had to order them. Mazdatrix had them for 12.00$ a piece and it cost like 5.50 for shipping. By the time you figure in Sales tax, I probably saved a little bit. But at least I knew what I was getting. The guy at the dealer wasn't too familiar with the 13B.

Dealer or Mazdatrix. Pep Boys may be have one.

they have it in stock at schucks for $13.99 guess that solves that problem.

Thats cool! https://www.nopistons.com/forums/pub...#>/BURNOUT.gif

That's a damn good price.

Nice ride, I hope im as lucky when I go to look for mine

Keep an eye open for 10th AE badges I need them and they are fuggin out of site brand new.

I also have an 89 flywheel from a tII. IF you want it send me a pm. BTW what is this s4, s5 stuff? Also who makes a good fuel filter for a 90tII?

S4 87-88 S5 89-91 . aka less typing LOL. fuel filter doesn't really matter i use purolator

Got one, should be here by Thursday, where were you yesterday LOL I do appreciate the offer though. Yea speaking of fuel filters, I am in the same boat, I stuck a temporary one in the 10th AE until I could find something better then the fram pile of ****.

Sorry I was doing that quality time thing with my wife. Its all good though b/c I still can use it on my car when my clutch goes. It will save me from having to wait for mine to be reserfaced.

Wow, phinsup you are amazingly lucky https://www.nopistons.com/forums/pub...DIR#>/moon.gif lol. Up here in Canada 10th aniv. ed.'s are as rare as a ricer civic ... wait a minute something seems wrong there, lmao https://www.nopistons.com/forums/pub...#>/biggrin.png

I'll snap some exterior pics on Saturday after I do a wax job. I am very excited to get to drive it. I went and got it registered at lunch today so I am good to go!

Well I'm picking up the brake master cylinder tomorrow, and I might order a few other things for the AE. Phinsup, would you be down for having a little AE fixing party this weekend?

Yea that would be great! We'll have the compressor running over time.. we may even get time to yank the tranny out of the 84 if we finish both the AE's! Then we can go for a spin!

Anyone out there know of a good place to get some cross drilled rotors for a good price?

EEEK, the only disadvantage is you can't have them turned! Lemme look around. You need them by this weekend?

I just figured it would be fun to put them on. I am collecting on the bet that I won today, so I've got some $ burning a hole in my pocket. https://www.nopistons.com/forums/pub...#>/biggrin.png I'm getting a swtarion IC from Rotaryman88, maybe I'll just buy something else, like a BOV and boost controller. I'll figure it out tonight. Well, gotta go to work now. :(

We gotta get my boost guage and controller switchy dealy bobber working on saturday too, still no locks for it yet though...

Ive had good luck with my slotted rotors, and the hubs dont rust out, which is a definite plus, I can snap a pic if you like?