|
Well I shouldn't say cold its actually warm here.I am currently swapping a Carbed 6-port 13b into my 1988 B2200 short box pickup.What are you guys doing?
|
im rebuilding the cosmo motor again, also found out my chassis is tweeked so im currently working on straighting the floor and chassis then roll cage to strengthin everthing. and a bigger turbo set up as well as other things to the fc
|
I'm replacing the auto tranny in a Honda Accord and deciding if I'm swapping out my broke gsl-se 13b for a 2nd gen 13b or rebuilding.
|
Peripheral port 86!
|
Diff, dyno and spray. Gotta get the wideband working too. Actually, I've mostly been working on wiring someone else's car.
|
rebuilding a 13b-re full bridged. stripping the fc, fitting new body panels, having it painted, building a cage, Then swaping the re motor it into my fc, and then adding ten thousand parts to support. then crying cause im happy its so gorgous and sad i wont have any money left to drive it! so im pretty busy!
|
Pretty much a top-to-bottom rebuild of everything. Not much winter left tho.
http://www.satc.net/rx7/cage2.jpg Just got the 6-point finished... http://www.bfhracing.org/duck/nofenders3.jpg Stripped it down, prepping for new body panels... http://www.satc.net/rx7/bed/bed02.jpg Going to use the body panels I used to make my SA22 bed on the car... http://www.ludwigmotorsports.com/rx7/gt42r.JPG Old turbo on the left, new turbo on the right... It's coming a long tho. The new rear-end is almost done. Can't wait to swap over to 5-bolt! |
|
Nice bed ducktape.I was thinking of doing with my frame rusted 83.Cut the unibody off at the fire wall and go from there.Looks good.
|
Originally Posted by nismo convert' post='807018' date='Mar 9 2006, 04:21 PM
|
|
What's new since my last post:
Submitted rotor housings for machining and sleeve insertion Assembled dual throttles I'm using two protege throttle bodies, one for each rotor. I know it seems complicated but everyone said that about putting a TII LIM on a 6 Port block. |
Will this thing run this year Colin?
For those in the area, come by Speedorama London this weekend. Got a little somethin, somethin. |
Well started last fall when my last engine took a dump.
Build a new motor, new turbo setup and new ems. Motor and turbo is in car . Still have lots to do and barely any time. pic of the motor http://img212.imageshack.us/img212/9858/dsc023158xc.jpg |
Originally Posted by Racer X' post='807360' date='Mar 11 2006, 09:06 AM
Now that a crazy project.I did a similar one with my salvage yarded 84 GT-X project tho.My fuel tank was where my passanger seat is now. https://www.nopistons.com/forums/pub...DIR#>/cool.png That definilty looks like a good project. |
Originally Posted by TYSON' post='809469' date='Mar 23 2006, 12:40 AM
Will this thing run this year Colin? For those in the area, come by Speedorama London this weekend. Got a little somethin, somethin. **** I wish you called me man. I would have dropped by no doubt! I keep working trying to get ahead but I don't know. I have debt to take care of before the RX7 hits the road again, but keep in mind I have all the parts I need to drive the car, less the engine hard/soft seal kit to put it back together. I'm not buying the seal kit before my bills are lifted. But I have everything else! So I guess squaring up my debt is technically progress on the car, but it's harder to gauge than just buying parts piece by piece to build a peripheral port. I like working on the car without spending money, but I can only go so far before I need the seals! |
I did F all this winter. Now my project is turning into a spring time rush job.
|
| All times are GMT -5. The time now is 05:11 AM. |
© 2024 MH Sub I, LLC dba Internet Brands