Ok... So the plan is:
Nippondenso pump (or similar) 550cc pri / 1300cc sec Rising rate regulator stock rails What I want to do is: Run steel braided lines from the driver side firewall (where the lines come from under the car) to the FPR and rails. Anybody have this setup? Can you provide me a list of the required fittings and sizes, lines lengths/sizes and anything else I'll need to piece this together? TIA! |
I wouldn't run 1300's due to the horror stories I've heard about them. Go with 1600's and a different rail.
Don't have the setup yet but when you figure it out let me know;) |
You know... I just noticed SR has:
1700cc Bosche Injectors These top feed , low impedence high flow injectors, may be just what you need for your high HP fuel flow needs. 129.00 each! Damn... I guess I could get these and a rail huh? |
When I get home I'll PM you a place to get injectors from. You can get 2 for that price. They are actually 1680cc, SR must be rounding up the #'s.
|
i got my injectors for $80 each from precisionte.com . i would go 1600's it's harder to setup but you don't have to worry about them failing!
|
Originally Posted by vosko' date='Jul 23 2003, 02:38 PM
i got my injectors for $80 each from precisionte.com . i would go 1600's it's harder to setup but you don't have to worry about them failing!
|
interested on the braided lines as well..
|
O.K. since everyone seems to want to know.
Marren fuel injection www.injector.com they quoted me $75 per injector. I was thinking it was $65 but I just double checked and its $75ea. This is for Bosch low impedance top feed units. |
Originally Posted by 93 R1' date='Jul 23 2003, 04:23 PM
This is for Bosch low impedance top feed units.
|
I have just started changing my fuel system out from the stock lines before I go and get tuned. I am running 2 walbro in tank to a Y into -8 hard line (cheaper) then when they get to the front I Y them into 2 -6lines(550/ 1600), one to each rail. Then in to the fuel pressure regulator and back into the stock return line. I am still putting it in and am about 50% done, I will post some pictures of what it looks like when I am done. I order about $400 dollars worth of line and fittings from Jegs, but I have some extra fittings. Didn't want to be one fitting short!
|
Originally Posted by 93 R1' date='Jul 23 2003, 12:08 PM
I wouldn't run 1300's due to the horror stories I've heard about them. Go with 1600's and a different rail.
Don't have the setup yet but when you figure it out let me know;) |
https://www.nopistons.com/forums/pub...1047683621.gif but whats with that damn cow sig???
|
Originally Posted by IGGER-IKE-EW-FD3S' date='Jul 23 2003, 02:43 PM
[quote name='93 R1' date='Jul 23 2003, 12:08 PM'] I wouldn't run 1300's due to the horror stories I've heard about them. Go with 1600's and a different rail.
Don't have the setup yet but when you figure it out let me know;) also if you go with the 1600 >1680cc injectors dont forget to get the resistors to solder in and the new connectors for the injectors |
Originally Posted by Travisty' date='Jul 23 2003, 02:45 PM
https://www.nopistons.com/forums/pub...1047683621.gif but whats with that damn cow sig???
|
Originally Posted by IGGER-IKE-EW-FD3S' date='Jul 23 2003, 05:48 PM
thats my buddy the moderator messin with me
ok back to the thread that i have no knowledgable input on |
https://www.nopistons.com/forums/pub...1047683621.gif by the way can someone mess with dragon as a payback for messing with my signature https://www.nopistons.com/forums/pub...1047683329.gif please https://www.nopistons.com/forums/pub...O_DIR#>/11.gif please https://www.nopistons.com/forums/pub...1047683785.gif
|
i can supply you with
the secondary rail and mounting hardware 2 new 1680cc injectors and the clips a tapped primary rail (OEM so all you have to do is pop your current injectors in) ALL the braded line and fittings already assembled resistors if running a PFC this will replace your fuel system form the firewall up and back... basicly a bolt on and all you have to supply is a regulator and fuel guage. (i can do that for additional also) takes all the guess work out of the process. the price for all this is $510 shipped. https://www.nopistons.com/forums/pub...DIR#>/wink.png if you want a breakdown rail= $130 1680cc injectors =$150 (for both) all needed lines and fittings pre assembled =$220 injector clips = included resistors already soldered on clips= included... $10 shipping total= $510 if you would like the rail anodized any special color just ask. https://www.nopistons.com/forums/pub...DIR#>/wink.png BTW, i would need a refundable deposit until i recieve your primary rail. https://www.nopistons.com/forums/pub...IR#>/smile.png any interest just email me rxrotary2_7@yahoo.com |
i have top feed primary rails too.... http://www.3rdgenrx7.com/keithsrails.htm
|
where were you when I bough mine? It would be nice to get a package deal. Group Buy? Could help alot of people out, if you could support that.
|
i have been around. there are many people with the setup already. https://www.nopistons.com/forums/pub...DIR#>/wink.png
group buy? i'm down. i would need some money up front if that were to happen just to make sure i dont get burned before going and investing in $1,000,000 worth of crap. https://www.nopistons.com/forums/pub...DIR#>/wink.png |
You can see if there is any interest, no one likes to get screwed over. Start small with maybe 5 or 10 and see how it goes.
|
not really interested in *seeing how it goes* though... if someone is serious enough to buy the whole deal, i highly doubt that a $200 PRE payment and about a weekish wait is to much to ask. if someone would not be willing to do that then they can fend for themselfs so to speak. i have a good enough reputation of being honest guy between the two boards, ebay, partstrader and just plain people knowing me. https://www.nopistons.com/forums/pub...DIR#>/wink.png
|
I don't want you to get ripped off.
|
oh i know that! https://www.nopistons.com/forums/pub...DIR#>/wink.png https://www.nopistons.com/forums/pub...IR#>/smile.png and i am not trying to rip anyone off... hell rx7.com sells JUST the rail and injectors for $598... BUT no pre assembled lines/fittings that will total out to about $200 easily, no shipping included, i dont believe they include injector clips (about $10 each), the rail design they use will not allow you to upgrade to a top feed primary anytime down the road really....
|
wow...renewed interest in fuel. This is what I run:
2 stock FD pumps...one for the primary and one for the secondary. 2 1680cc top feed low impedance bosch injectors 2 550cc stock injectors PPR 2ndary fuel rail with -6 a/n fittings Stock primary rail tapped with 3/8 npt and -6 a/n fittings aeroquip fpr(which is also they "Y") Return line via the stock metal lines that went to the charcoal canister. Bulk head fitting on the fuel pump assembly as the return. all -6 and a/n fittings. NEVER had any problems with fuel except for tightening down a/n fittings too tight. https://www.nopistons.com/forums/pub...IR#>/blink.png |
Originally Posted by rxrotary2_7' date='Jul 23 2003, 10:02 PM
i can supply you with
the secondary rail and mounting hardware 2 new 1680cc injectors and the clips a tapped primary rail (OEM so all you have to do is pop your current injectors in) ALL the braded line and fittings already assembled resistors if running a PFC this will replace your fuel system form the firewall up and back... basicly a bolt on and all you have to supply is a regulator and fuel guage. (i can do that for additional also) takes all the guess work out of the process. the price for all this is $510 shipped. https://www.nopistons.com/forums/pub...DIR#>/wink.png if you want a breakdown rail= $130 1680cc injectors =$150 (for both) all needed lines and fittings pre assembled =$220 injector clips = included resistors already soldered on clips= included... $10 shipping total= $510 if you would like the rail anodized any special color just ask. https://www.nopistons.com/forums/pub...DIR#>/wink.png BTW, i would need a refundable deposit until i recieve your primary rail. https://www.nopistons.com/forums/pub...IR#>/smile.png any interest just email me rxrotary2_7@yahoo.com |
Originally Posted by 9BASE3' date='Jul 24 2003, 11:14 PM
[quote name='rxrotary2_7' date='Jul 23 2003, 10:02 PM'] i can supply you with
the secondary rail and mounting hardware 2 new 1680cc injectors and the clips a tapped primary rail (OEM so all you have to do is pop your current injectors in) ALL the braded line and fittings already assembled resistors if running a PFC this will replace your fuel system form the firewall up and back... basicly a bolt on and all you have to supply is a regulator and fuel guage. (i can do that for additional also) takes all the guess work out of the process. the price for all this is $510 shipped. https://www.nopistons.com/forums/pub...DIR#>/wink.png if you want a breakdown rail= $130 1680cc injectors =$150 (for both) all needed lines and fittings pre assembled =$220 injector clips = included resistors already soldered on clips= included... $10 shipping total= $510 if you would like the rail anodized any special color just ask. https://www.nopistons.com/forums/pub...DIR#>/wink.png BTW, i would need a refundable deposit until i recieve your primary rail. https://www.nopistons.com/forums/pub...IR#>/smile.png any interest just email me rxrotary2_7@yahoo.com go with the aeroquip FPR. when my wastegate line blew off and I boosted 2.6 kilos(that is not a typo btw), my fuel pressure actually held just fine...course my motor didn't but that's another story. https://www.nopistons.com/forums/pub...IR#>/blink.png |
Originally Posted by jspecracer7' date='Jul 24 2003, 08:17 AM
when my wastegate line blew off and I boosted 2.6 kilos
Holy ****! |
Originally Posted by 9BASE3' date='Jul 24 2003, 11:25 PM
[quote name='jspecracer7' date='Jul 24 2003, 08:17 AM'] when my wastegate line blew off and I boosted 2.6 kilos
Holy ****! [/quote] lol...I acutally guessed it was 2.6... My defi gauge reads only to 2.0 kilos boost. The "Peak" needle was actually at "E"...as in P(needle here)AK...lol |
Holy **** is right, damn LOL!!!!
|
i second that "HOLY ****" what did it sound like?? do the tires chirp at that much boost?
|
Originally Posted by fastcarfreak' date='Jul 28 2003, 02:34 PM
i second that "HOLY ****" what did it sound like?? do the tires chirp at that much boost?
|
Originally Posted by jspecracer7' date='Jul 28 2003, 04:15 AM
I was on a roll, I have drag suspension(HKS Hiper D Drag) and had 275 BFG Comp T/A's...tires didn't chirp...but I tell ya what...It was a MEAN SOUNDING SOB that 9 seconds that it lasted...lol
|
Originally Posted by 9BASE3' date='Jul 28 2003, 11:42 PM
I'm guessing a clean pair of underwear was on order after that run? https://www.nopistons.com/forums/pub...1047683664.gif
|
Ok.. I talked to Keith. He's going to set me up the bomb! Haha.. Sorry couldn't resist!
Can't wait to start bolting **** back together!!! |
Bump for interest. https://www.nopistons.com/forums/pub...#>/biggrin.png
|
how the **** did i miss this one.
Kieth. I want a set. https://www.nopistons.com/forums/pub...IR#>/blush.png email me fd3boost@comcast.net Dave |
All times are GMT -5. The time now is 04:43 AM. |
© 2024 MH Sub I, LLC dba Internet Brands