2nd Generation Specific 1986-1992 Discussion

starting issues

Thread Tools
 
Search this Thread
 
Old 08-22-2007, 06:51 PM
  #1  
Junior Member
Thread Starter
 
RHex-7's Avatar
 
Join Date: Jul 2007
Location: cal
Posts: 28
Default

recently i when to start my 86 s4 and when i turned on the car it wold start but it whold die not just stright up die but lose rpms till it whold just die but if i give it a stedy throttel (wile in nutral) it will stop and idel right and not die any one have any ideas on what it could be? ( resently took off both mufflers due to holes in them and going to replace i was thinking maybe its because of that maybe not enough back pressure
RHex-7 is offline  
Old 08-23-2007, 11:42 AM
  #2  
Junior Member
 
wwshadowfoxww's Avatar
 
Join Date: Mar 2007
Location: Key West Fl
Posts: 27
Default

if it has been sitting for a while try draining out the old gas
wwshadowfoxww is offline  
Old 08-23-2007, 12:59 PM
  #3  
Junior Member
Thread Starter
 
RHex-7's Avatar
 
Join Date: Jul 2007
Location: cal
Posts: 28
Default

hasent been sitting gas if new
RHex-7 is offline  
Old 08-23-2007, 01:18 PM
  #4  
Junior Member
 
mazda.junkie's Avatar
 
Join Date: May 2007
Location: Cruso NC
Posts: 20
Default

1)What does it do when it warms up?



2)The mufflers will not effect the idle



3)Sounds like a vaccum issue to me
mazda.junkie is offline  
Old 08-23-2007, 07:05 PM
  #5  
Junior Member
Thread Starter
 
RHex-7's Avatar
 
Join Date: Jul 2007
Location: cal
Posts: 28
Default

Originally Posted by RHex-7' post='880962' date='Aug 22 2007, 04:51 PM
recently i when to start my 86 s4 and when i turned on the car it wold start but it whold die not just stright up die but lose rpms till it whold just die but if i give it a stedy throttel (wile in nutral) it will stop and idel right and not die any one have any ideas on what it could be? ( resently took off both mufflers due to holes in them and going to replace i was thinking maybe its because of that maybe not enough back pressure
once it warms up its fine and and i waas thinking vaccum leak too but thir isent one
RHex-7 is offline  
Old 08-23-2007, 09:42 PM
  #6  
Junior Member
 
mazda.junkie's Avatar
 
Join Date: May 2007
Location: Cruso NC
Posts: 20
Default

Try removing the vaccum line that runs to the pressure sensor. Its on the front of the strut tower on the passenger side. The car may still die the first time you start it but start it again, and that should bring the idle to normal if the sensor is bad. Mine used to die about 3 times before I could coax it into holding idle, and then after a minute or two the idle would go from 1500rpm down to 600rpm then back up. The pressure sensor was bad. If that doesnt work, let me know and Ill give you option B lol.
mazda.junkie is offline  
Old 08-24-2007, 03:05 PM
  #7  
Junior Member
Thread Starter
 
RHex-7's Avatar
 
Join Date: Jul 2007
Location: cal
Posts: 28
Default

yep i think its my pressure sensor unpluged the vacum hose and it dosent die anymore thax
RHex-7 is offline  
Old 08-24-2007, 05:28 PM
  #8  
Junior Member
 
mazda.junkie's Avatar
 
Join Date: May 2007
Location: Cruso NC
Posts: 20
Default

Originally Posted by RHex-7' post='881199' date='Aug 24 2007, 04:05 PM
yep i think its my pressure sensor unpluged the vacum hose and it dosent die anymore thax


No problem man, glad I could help. It took me awhile to source the same problem, but it will run fine without it.
mazda.junkie is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
NavyFD3S
3rd Generation Specific
12
12-03-2012 11:02 PM
rx7man629
2nd Generation Specific
4
07-08-2005 07:38 PM
Seppuku
2nd Generation Specific
9
12-08-2003 08:38 PM
ryosuke_fc
Rotary Engine Building, Porting & Swaps
26
10-14-2003 09:11 PM
amp
2nd Generation Specific
11
02-25-2003 11:06 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 


Quick Reply: starting issues



All times are GMT -5. The time now is 12:00 PM.