2nd Generation Specific 1986-1992 Discussion

Engine Cut...

Thread Tools
 
Search this Thread
 
Old 11-05-2008, 11:24 PM
  #1  
Junior Member
Thread Starter
 
rotorhead_fc's Avatar
 
Join Date: Oct 2008
Location: B.C.
Posts: 11
Default

Hey i just got an n/a FC project car and it has been sat for two years until i bought it. I just started i up today and it runs fine other than puking out a **** load of smoke until it warmed up! Only issue motor wise so far is that when i try to rev it up it hits 4grand and then cuts out back to idle. When i say it cuts out it doesnt actually shut off it just stops and the rpms drop until i take my foot off the gas and re apply it.



Any ideas what it could be? TPS buggered?



And as an FYI it wont n/a for long! Just need to get it running and have it as a secondary run around car until i build up a bt!



Thanks in advance!
rotorhead_fc is offline  
Old 11-06-2008, 07:43 AM
  #2  
Member
 
jamest16748500's Avatar
 
Join Date: Oct 2008
Location: JAX FL
Posts: 50
Default

umm. kinda sounds like it's going into limp mode check to see if the omp if functioning properly. otherwise if it's smoking on start up could be the tps if you have a s5 b/c one of the tps control the oil injection i think this is corroct some one correct me if i'm wrong.
jamest16748500 is offline  
Old 11-11-2008, 07:46 AM
  #3  
Junior Member
 
kagoshima's Avatar
 
Join Date: Oct 2008
Posts: 14
Default

probably chocked full of oil before sent to australia

www.kagoshimaenglish.com
kagoshima is offline  
Old 11-11-2008, 11:53 AM
  #4  
Junior Member
 
merlia joseph's Avatar
 
Join Date: Nov 2008
Posts: 1
Default

do you have any more clearance?
merlia joseph is offline  
Old 11-11-2008, 03:52 PM
  #5  
Junior Member
Thread Starter
 
rotorhead_fc's Avatar
 
Join Date: Oct 2008
Location: B.C.
Posts: 11
Default

Hey Merlia joseph unless you have useful input, dont post here
rotorhead_fc is offline  
Old 11-11-2008, 03:58 PM
  #6  
Junior Member
Thread Starter
 
rotorhead_fc's Avatar
 
Join Date: Oct 2008
Location: B.C.
Posts: 11
Default

Originally Posted by kagoshima' post='911459' date='Nov 11 2008, 05:46 AM
probably chocked full of oil before sent to australia

www.kagoshimaenglish.com


Did you mean to say, send the engine to Australia? Ill sell you the engine, trans and ecu for cheap. It runs, just hesitates at 3800rpm
rotorhead_fc is offline  
Old 11-11-2008, 06:39 PM
  #7  
Member
 
jamest16748500's Avatar
 
Join Date: Oct 2008
Location: JAX FL
Posts: 50
Default

Originally Posted by rotorhead_fc' post='911506' date='Nov 11 2008, 02:58 PM
Did you mean to say, send the engine to Australia? Ill sell you the engine, trans and ecu for cheap. It runs, just hesitates at 3800rpm


try this thread https://www.nopistons.com/forums/Fc-Groundi...Stu-t48183.html

or you could sell it to me j/k
jamest16748500 is offline  
Old 11-11-2008, 09:02 PM
  #8  
Junior Member
Thread Starter
 
rotorhead_fc's Avatar
 
Join Date: Oct 2008
Location: B.C.
Posts: 11
Default

Originally Posted by jamest16748500' post='911518' date='Nov 11 2008, 04:39 PM
try this thread https://www.nopistons.com/forums/Fc-Groundi...Stu-t48183.html

or you could sell it to me j/k


Haha sure its yours for $500! lol. Thanks for the link im going to give that a shot
rotorhead_fc is offline  
Old 11-13-2008, 09:57 AM
  #9  
Senior Member
 
jwteknix's Avatar
 
Join Date: Sep 2005
Location: Wayne NJ
Posts: 1,440
Default

what year is your car?
jwteknix is offline  
Old 11-16-2008, 03:35 AM
  #10  
Junior Member
Thread Starter
 
rotorhead_fc's Avatar
 
Join Date: Oct 2008
Location: B.C.
Posts: 11
Default

Originally Posted by jwteknix' post='911619' date='Nov 13 2008, 07:57 AM
what year is your car?


its an 86 gxl n/a. All it does at the moment is get to around 3800 and then drop right off back to idle. I noticed in the other post you said it could be in limp mode? The other guy at the beginning of the thread mentioned that also. Im not getting an engine light though so i dont know if its throwing any codes at all. Going to check the warning lights and make sure they're all working first!



Im assuming limp mode would be a safe mode for the car? What causes this usually?



Thanks in advance
rotorhead_fc is offline  


Quick Reply: Engine Cut...



All times are GMT -5. The time now is 05:48 AM.