1st Generation Specific 1979-1985 Discussion

My car will be ready this spring

Thread Tools
 
Search this Thread
 
Old 09-23-2005, 04:16 PM
  #1  
Senior Member
Thread Starter
 
rootbeerdragon's Avatar
 
Join Date: May 2004
Location: Minnesota!
Posts: 452
Default

Ill be getting my license this up comming spring, and ill be using this car as a daily driver, which means ill probably be using it in the winter.. as much as i dont want to obviously but i have no choice.. my question is that it will be hard to start my car in the cold *** minnesota temperature, i already have msd ignition, ngk plugs/wires, but how can i go about getting my car started efficently in the winter?
rootbeerdragon is offline  
Old 09-23-2005, 04:21 PM
  #2  
Senior Member
 
rowtareh's Avatar
 
Join Date: Jan 2004
Location: Columbia IL/St. Louis MO
Posts: 2,748
Default

your GS is carb'd right? honestly, in my experience with carbs(which is not very much), starting a carb'd engine even in maryland winter's sucked. it would die within 30 seconds if you let it idle on it's own.



how cold does it get in minnesota during the winter time? and i wonder if you can use engine starting fluid? whatever that **** is called, i forget.
rowtareh is offline  
Old 09-23-2005, 04:47 PM
  #3  
Senior Member
 
Shane.Trammell's Avatar
 
Join Date: May 2002
Location: Richardson Texas
Posts: 4,326
Default

engine heater?
Shane.Trammell is offline  
Old 09-23-2005, 05:41 PM
  #4  
Senior Member
Thread Starter
 
rootbeerdragon's Avatar
 
Join Date: May 2004
Location: Minnesota!
Posts: 452
Default

it can get cold, but in minnesota the the weather is unexpected, 75mph winds 2 days ago..



so your saying carry a bottle of heat in my backpack?? lol
rootbeerdragon is offline  
Old 09-23-2005, 05:54 PM
  #5  
Senior Member
 
rowtareh's Avatar
 
Join Date: Jan 2004
Location: Columbia IL/St. Louis MO
Posts: 2,748
Default

i always used it when working construction, ether or it was engine starter fluid. worked really well on the diesels during the cold days. especially at 6am when the temperature was at 15 degrees or below.



i don't know about doing it though, if it would be a harsh material to the engine. it says it worked on diesel and gas engines. we even used it during the summer time on the **** that was hard to start up, it started right up after using about half the bottle. but that equipment was older than banzaitoyota, which is pretty old.
rowtareh is offline  
Old 09-23-2005, 09:48 PM
  #6  
Senior Member
Thread Starter
 
rootbeerdragon's Avatar
 
Join Date: May 2004
Location: Minnesota!
Posts: 452
Default

lol well im gunna try it, if it doesnt work im gunna have to get a job and find a reliable car that will get me places in the winter... still makes me mad that im gunna be ruining my car driving it in the winter.. ill probably get in an accident lol
rootbeerdragon is offline  
Old 09-23-2005, 11:07 PM
  #7  
Senior Member
 
rowtareh's Avatar
 
Join Date: Jan 2004
Location: Columbia IL/St. Louis MO
Posts: 2,748
Default

eh, it is only a car to be honest with you. i would check into trying the engine starter fluid though, i am not 100% sure of what it can do to a rotary engine.
rowtareh is offline  
Old 09-24-2005, 01:25 AM
  #8  
Fabricator
 
Lynn E. Hanover's Avatar
 
Join Date: Jan 2004
Location: Central Ohio (Hebron) Zephyrhills Fla.
Posts: 1,322
Default

Originally Posted by rowtareh' post='762268' date='Sep 23 2005, 08:07 PM

eh, it is only a car to be honest with you. i would check into trying the engine starter fluid though, i am not 100% sure of what it can do to a rotary engine.




Use WD-40 for starting fluid. The stock engines used to have a bottle that you put antifreeze in, and when the temps are low the antifreeze keeps the seals from sticking in the grooves when they run over frost inside the housings. WD-40 does the same thing and helps sealing a bit. Pouring boiling water on the intake manifold helps too, as does a block heater and, or, a spot light bulb tight against the oil pan to keep the oil loose.









Lynn E. Hanover
Lynn E. Hanover is offline  
Old 09-24-2005, 09:00 AM
  #9  
Senior Member
 
GreyGT-C's Avatar
 
Join Date: Mar 2003
Location: Disclaimer: posts made after 11AM are most likely alcohol induced. Please disregard unless very funn
Posts: 2,436
Default

get an engine block heater.
GreyGT-C is offline  
Old 09-24-2005, 09:12 AM
  #10  
Senior Member
Thread Starter
 
rootbeerdragon's Avatar
 
Join Date: May 2004
Location: Minnesota!
Posts: 452
Default

Originally Posted by rowtareh' post='762268
Use WD-40 for starting fluid. The stock engines used to have a bottle that you put antifreeze in, and when the temps are low the antifreeze keeps the seals from sticking in the grooves when they run over frost inside the housings. WD-40 does the same thing and helps sealing a bit. Pouring boiling water on the intake manifold helps too, as does a block heater and, or, a spot light bulb tight against the oil pan to keep the oil loose.

Lynn E. Hanover


lol theres no way im gunna have a boiling pot of water coming out of school.. and i dont know how much i would trust putting in wd40 in my carb... the only problem would be starting the car after school... before school it would be fine because i have a heated garage that stays at 75 degrees all summer.. so thats one thing thats good..
rootbeerdragon is offline  


Quick Reply: My car will be ready this spring



All times are GMT -5. The time now is 08:25 AM.