Ok,
First, to RacerX, sorry for mucking up your thead on clutch problems with timing questions. Now for the info. This is for setting the TOTAL advance @4000+RPM (NOT idle) Tools used: 1/4" drive ratchet with 12" extension and a 10MM socket. (my weapon of choice for loosening and tightening the distributer bolt) #2 phillips screwdriver with a 14" long shaft (weapon of choice for loosening and tightening trailing advance screws) (you can't bash your knuckles if your knuckles aren't near anything) Inductive timing light with advance (it's too much work for me to measure out all the degrees onto a piece of tape then align the zero's then apply the tape to the pulley then file marks representing the degrees hoping I don't screw up the pulley) My favorite throttle stick (a friend will work just as well) A word of caution: (To keep people from trying to sue me for them not being able to follow directions!) THE WANKLE MOTOR ACTS LIKE A 2 STROKE MOTOR AS FAR AS IGNITION! Meaning that evry time the 0 mark on the pulley comes up to the pointer, the ignition fires. So if your timing light DOESN'T have a 2 stroke option, then the setting values are cut in half. We will assume that you are using a light without the 2 stroke option. For more info on how a distributer works, YAW POWER has an excellent article here: http://personal.riverusers.com/~yawpower/pultime.html Read it now! I hope that site never goes away https://www.nopistons.com/forums/pub...#>/biggrin.png Now that all that B.S. is out of the way, we can start and warm up our engines. Read the above article for recommended total advance. Install timing light per Mfgr's instructions. (#1 leading plug) Set advance dial to 1/2 desired advance. Have trusted assistant hold rpm @ 4000. Check the timing against your 0 mark on pulley, it shouldn't be very far off. Loosen distributer and turn to align 0 mark and pointer. Tighten distributer. You've just set the leading timing! Congratulations! Give trusted helpers foot a rest while you move timing light to #1 trailing plug wire per Mfgr's instructions. Re-adjust advance dial to 1/2 your trailing spec. Have trusted assistant hold rpm @ 4000. Check the timing against your 0 (yes 0!) mark. Loosen the two set screws for the trailing advance vacuum pod. pull out on the vacuum pod to advance. Tighten screws. Re-check timing against 0 (yes 0!) mark. Re-adjust as necessary to get it aligned. Be patient. Try again. There you go, you've just set your trailing advance! You will hear a difference when you set the trailing advance. Tell trusted assistant to "beat it" and remove timing light. Go for a ride! Enjoy. After I set my timing I rechecked my Idle settings. I found that I am 2` advanced leading and 6`retarded trailing. Your results may vary based on the operation of the mechanical and vacuum advance systems in your distributer. |
Don't sweat it about my thread I don't mind.Good info you posted :bigok: Moderators: Could you guys move this to the FAQ section and Pin it?
Thanks Luis |
2 things. you might want to disconnect the vacuum advances to set the timing @4k, and i notice my gsl-se is a lot more responsive with paul yaw's 8 degree split, i didnt change the factory timing except to reduce the split.
mike |
Originally Posted by j9fd3s' date='Feb 2 2003, 04:34 PM
2 things. you might want to disconnect the vacuum advances to set the timing @4k, and i notice my gsl-se is a lot more responsive with paul yaw's 8 degree split, i didnt change the factory timing except to reduce the split.
mike |
I had noticed a difference in sound when I timed it, then when I drove it afterwards
I noticed my clutch slipping where it wasn't before. so I guess I have more power https://www.nopistons.com/forums/pub...#>/biggrin.png |
Originally Posted by Smog Fighter' date='Feb 2 2003, 09:25 PM
I had noticed a difference in sound when I timed it, then when I drove it afterwards
I noticed my clutch slipping where it wasn't before. so I guess I have more power https://www.nopistons.com/forums/pub...#>/biggrin.png |
Originally Posted by Racer X' date='Feb 2 2003, 09:34 PM
[quote name='Smog Fighter' date='Feb 2 2003, 09:25 PM'] I had noticed a difference in sound when I timed it, then when I drove it afterwards
I noticed my clutch slipping where it wasn't before. so I guess I have more power https://www.nopistons.com/forums/pub...#>/biggrin.png Until I realized that after 5 minutes of playing with my car I now need to spend $250-300 on a clutch. Plus the time to install it |
Originally Posted by Smog Fighter' date='Feb 2 2003, 09:58 PM
[quote name='Racer X' date='Feb 2 2003, 09:34 PM'] [quote name='Smog Fighter' date='Feb 2 2003, 09:25 PM'] I had noticed a difference in sound when I timed it, then when I drove it afterwards
I noticed my clutch slipping where it wasn't before. so I guess I have more power https://www.nopistons.com/forums/pub...#>/biggrin.png Until I realized that after 5 minutes of playing with my car I now need to spend $250-300 on a clutch. Plus the time to install it [/quote] Take it from me.I have first hand experience in this part.The clutch swap is easy just make sure that it will bleed afterwards. :rant: |
:rant:
|
j9fd3s, you're using 12A split on a 13B :redface: (unless it's better than the 10º he recommends for 13Bs). I'm gonna try switching my Trailing ignition off while driving under various loads and conditions to see if I lose any power. I'm running DLIDFIS with a carb here.
|
All times are GMT -5. The time now is 07:50 PM. |
© 2024 MH Sub I, LLC dba Internet Brands