OK, it is a TO4B, it has a 1.15 AR exhuast, and .60 intake. The shaft doesn't have alot of play, and from what I can tell it is in good shape.



I don't know to much about the turbo, but I can tell you were to find a rebuild kit for $60 bucks. The intake/exhaust wheels are both in very good shape, with no bent fins, or anything like that. Also the turbo spins very freely.



Here is pictures:





http://http://prod.bsis.bellsouth.ne...1manifold2.JPG



http://http://prod.bsis.bellsouth.ne...1manifold3.JPG



http://http://prod.bsis.bellsouth.ne...os1resized.JPG



http://http://prod.bsis.bellsouth.ne...os2resized.JPG







I will trade for a set of 6 TII injectors, they all need to be in the same series, as long as I get a set of 6, I don't care what series they are.





Or if you would just like to buy the turbo, give me $175+shipping...





Thanks

pictures aren't working

Pictures don't work...



Here are the links:



http://home.bellsouth.net/p/s/community.dl...view=thumbs&ck=



http://home.bellsouth.net/p/s/community.dl...view=thumbs&ck=



http://home.bellsouth.net/p/s/community.dl...view=thumbs&ck=



http://home.bellsouth.net/p/s/community.dl...view=thumbs&ck=

http://prod.bsis.bellsouth.net/coDat...1manifold2.JPG

http://prod.bsis.bellsouth.net/coDat...1manifold3.JPG

http://prod.bsis.bellsouth.net/coDat...os1resized.JPG

http://prod.bsis.bellsouth.net/coDat...os2resized.JPG

i might be interested in the turbo.... u sure the play is okay? have you used the turbo?

I've never used it. I was going to use it on my supra7, but as you can see I got a bigger turbo....





And I have had about 5 different turbo's around the gaurage so far, and this TO4/KKK K27 (the one pictured) are the two tightest turbo's I have gotten so far. The shaft play is minimal from MY experiance. It doesn't rub the housing, and really doesn't come close.

^

What is the turbine trim? If thats a P trim 1.15 is bridge territory

It'll still work though...



And I don't know the trim, I can't remeber the measurements to to figure out the trim...

Are you looking for high or low impedance injectors?

Either...



As long as they are 550-680cc injectors. I will definately even trade on 6.



Do you have any?

I'll have to look.I have a set of S5 injectors(550's),SE injectors(680cc rated but flow more like a 720)and the set of 4 injectors in my TII motor.I can test them to see if they are the same impedance level as the S5's.If so then I do have 6.I mounted that FMIC I got off you.Have you seen the pic of it in my garage?

So does that make my 1.32 A/R bridge territory?wanta be boosted: Why doesn't it matter on impedance?Do you have a standalone?You better hope that the ECU isn't picky about impedance loads.

Sweet! You got that IC mounted. I'll look for the thread, I ended up useing a stock 7MGTE IC...



And if you have 6 injectors of the same impudence that would be awsome!



And I don't know if I can do anygood with the 680's, unless you also have a set of those, because I've looked before, And I had trouble finding 2 in the same place...









My brother is wiring up the stock supra ECU to my car, so he can put the resistor box in, or take it out... But stock the ECU I have uses low impudence, so if you have a set of those, it is prefered, but like I said, it doesn't matter... We can make them work https://www.nopistons.com/forums/pub...#>/biggrin.png

Wow That IC is a squeze https://www.nopistons.com/forums/pub...#>/biggrin.png I think FB's have more room up front, because I couldn't fit a Volvo IC, and piping in front of my junk yard Taurus radiator....



As rx7club would say,



You got lucky, glad it worked out in the end.





hahaha, god I hate that....