13b bridgeport motor set. 3mm apex seal,se rotors, 58mm ida weber gene berg with port manifold, 2 msd coils, custom header, rb flywheel,act pressure plate,rb 4 puck disc, recently gone trough trans with mazda trix short shifter, new starter, schattersheild, cater fuel pump,fram gas filter,holley regulator,rb plug wires,duel pulleys. put down 200rwhp with old twin weber set puts more down now.. nearly turn key. fits into 1st gen rx-7. dlesky@cfl.rr.com for pics or more info...$3500 obo...
|
$2500 obo burning a little oil.......
|
$2250obo
|
|
Where is this located?
|
I'm in central florida,Titusville ...orlando's beach front ......Dave.
|
maybe parting out ...or $2005obo Thanks dave...
|
do you have a dyno sheet you could post? id like to see where the power is
and how would this be for a dd? is the mileage bearable? |
I was told when I bought it it had between 10-15k and I put 4500k on it...The oil seals are geting to the point were oil is added at about 1/4 quart every 120miles..I have a dyno sheet of the older twin weber dcd's ,I don't know how to post it here but if you e-mail me dlesky@cfl.rr.com Icould send them to you...The carb is alone $1000 so if you part it out it is a good deal....
Price brake down gene berg 58mm ida $950 racingbeat intake ported by kilo racing $350 scatter sheild $150 short shifter $150 lightweight flywheel $250 moroso aluminum oil pan $300 dual coils $40 carter street strip pump $40 fram gas filter $40 holley fuel pressure reg. $30 racingbeat wires$40 new 4 puck disc. $50 act pressure plate$ 200 trans just gone threw and shifting good..... I bought the motor for $2500 and changed the intake and got it tuned by Kilo racing...It runs strong and I'm sure it put 225plus to the ground ,it needs seals and i'm going turbo so I don't want to put any more into this set up....I'm sure it would go 12's with a lighter car....Thanks Dave... |
nm since it needs seals, it is a good deal though
|
$2000 .....Bump
|
Going to part out on boards then e-bay...I have pay-pal...
gene berg 58mm ida and racingbeat intake ported by kilo racing $1000 scatter sheild $100 for 2nd gen rx7 13bnon-turbo short shifter $125 comes with shift ball and aluminum bushing lightweight flywheel $150 moroso aluminum oil pan $200 dual coils $40 carter street strip pump $20 fram gas filter $20 holley fuel pressure reg. $15 racingbeat wires$20 new 4 puck disc. $50 act pressure plate$ 100 may do trans w/short shifter $300 has 89 bellhousing fit first gen rx7 may do engine block w/pan and lightweight flywheel w/clutch assy $600 the motor needs rebuild oil seals and the frount rotor has low compression has 3mm apex seals ,bridgeport, and I put 4500 miles on it I was told it had 10k to 15k when I bought it..I can get pics of everything just e-mail .....dlesky@cfl.rr.com motor still in car,so it have to take out....Dave |
Carb, manifold, fuel pump,filter and regulator sold....
still for sell trans with shift kit and just gone threw $250 scatter sheild $100 liteweight flywheel, bridgeport motor w/low compression on frount rotor with moroso oil pan with alt,duel pulleys, water pump $600 3" header $150 h/d clutch w/ 4 puck disk $100 2 msd blaster 2 coils with tric billet mount $50 all parts 4500miles excpt. motor or best offer e-mail for pics dlesky@cfl.rr.com thanks dave |
All times are GMT -5. The time now is 12:41 AM. |
© 2024 MH Sub I, LLC dba Internet Brands