Rotary Engine Building, Porting & Swaps All you could ever want to know about rebuilding and porting your rotary engine! Discussions also on Water, Alcohol, Etc. Injection

13b Bridgeport with 48mm Weber IDA going rich between 5500-7000 rpm why?

Thread Tools
 
Search this Thread
 
Old 07-09-2017, 02:48 PM
  #1  
Junior Member
Thread Starter
 
butcheryboy's Avatar
 
Join Date: Mar 2008
Posts: 22
Default 13b Bridgeport with 48mm Weber IDA going rich between 5500-7000 rpm why?

Hey guys, 13b Rx4/5 engine running carbon seals used in a rally car, in the off season we decided to give her a total over haul/freshen up, all new seals, springs, lightened the rotors, side clearance, FD Rear oil reg, new oil pump etc as well as adding a moderate size (4mm thick) CNC cut bridge to the existing intake ports (as from the pics which was rather large Stage 2/Extend Port, with way oversized exhaust ports courtesy of the previous engine builder)

Once we got her up and running and run in enough, off to the dyno we went, and strangely although the bridgeport made more power than the stage 2, it has this weird flat spot (caused by rich conditions as observed by the AFR/lambda meters) that starts at 5500rpm but clears at 7000rpm as you can see. Nothing we tried improved it…which is a problem as in a rally car that’s is where you want the most power and most torque but due to the rich conditions we are down in that area.

On the dyno sheets Thick red line is the new bridgeported engine, thin red line the old Stage 2/extend port.

In terms of Carb tuning we have NOT changed a thing from the previous tune…
48mm Weber IDA
42mm Chokes
F11 Tubes
205 Mains
120 Airs
70F10 Idles
.70 Acc Pump
6mm Gross Fuel Inlet Jet with 4 PSI pressure

Running 98 Octane Pump gas premixed @ ratio 150:1

Timing is at 24 BTDC Leading ~20 BTDC Trailing
Exhaust is 2x slip jointed 2” primaries straight through collected just before the diff into muffler.

The ONLY thing that has been changed apart from the bridgeporting and timing slightly increased, is adding a straight through resonator (stainless packed) on each primary 2/3 of the way down.

In terms of AFR's I know it would be helpful if they were on the dyno sheet but they werent included on the print out, but I can assure you that at WOT @ 7000-8000rpm they were pretty much spot on, which surprised me as I thought we would be needing bigger mains given the additional porting but it seems not...?

Any ideas on what would cause this rich area and advice/tips to remedy would be great.

Brendon
Attached Thumbnails 13b Bridgeport with 48mm Weber IDA going rich between 5500-7000 rpm why?-fullsizerender.jpg   13b Bridgeport with 48mm Weber IDA going rich between 5500-7000 rpm why?-fullsizerender2.jpg   13b Bridgeport with 48mm Weber IDA going rich between 5500-7000 rpm why?-img_6356.jpg  

Last edited by butcheryboy; 07-09-2017 at 03:57 PM. Reason: Forgot some information again
butcheryboy is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
butcheryboy
Rotary Engine Building, Porting & Swaps
6
05-22-2012 11:48 PM
RX200013B
2nd Generation Specific
3
02-26-2010 10:34 AM
butcheryboy
Rotary Engine Building, Porting & Swaps
7
04-16-2009 04:24 PM
chrisw80
2nd Generation Specific
1
08-05-2007 11:58 AM
NoeVuh
2nd Generation Specific
2
06-13-2006 01:43 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 


Quick Reply: 13b Bridgeport with 48mm Weber IDA going rich between 5500-7000 rpm why?



All times are GMT -5. The time now is 12:00 PM.