NoPistons -Mazda Rx7 & Rx8 Rotary Forum

NoPistons -Mazda Rx7 & Rx8 Rotary Forum (https://www.nopistons.com/)
-   Rotary Engine Building, Porting & Swaps (https://www.nopistons.com/rotary-engine-building-porting-swaps-55/)
-   -   Streetable pp engine. (https://www.nopistons.com/rotary-engine-building-porting-swaps-55/streetable-pp-engine-73666/)

banzaitoyota 01-12-2010 07:00 PM

I should but my P-Port back together, since I discovered "a certain engine builder" did a crappy ass job of assembling it

89 Rag 01-13-2010 03:39 AM


Originally Posted by TYSON (Post 837569)
yeah you could feel the breeze from mine back about 15 feet. When I backed it out of there the first time with the open header it cleared 1/2" gravel off a spot 10 inches wide and 3 feet long under the car



That's incredible!

heretic 02-13-2010 08:16 PM


Originally Posted by j9fd3s (Post 837559)
its amazing how much exhaust energy there is, especially at idle.



mine blows rags around the shop, and the bushes 10+ feet away





Well, if you think about it, if engine vacuum is really low, like 4" of mercury or so, then the engine is almost running the equivalent of wide open throttle, right there at idle.



For a given exhaust system, a peripheral port exhaust won't be much louder than a street port when under the same load. The trick is, at idle and such the peripheral port is struggling to stay running so it's effectively under a lot of load.



A lot of noise comes from the intake tract at higher throttle openings, and there isn't much you can do about that.



I drove one around like a normal car, the only difference was like you noticed, you have to be accelerating or decelerating, if you just try to cruise then it shakes the fillings out of your teeth. It was quite oderiferous at stoplights.

j9fd3s 02-17-2010 02:45 PM


Originally Posted by heretic (Post 838622)
Well, if you think about it, if engine vacuum is really low, like 4" of mercury or so, then the engine is almost running the equivalent of wide open throttle, right there at idle.



For a given exhaust system, a peripheral port exhaust won't be much louder than a street port when under the same load. The trick is, at idle and such the peripheral port is struggling to stay running so it's effectively under a lot of load.



A lot of noise comes from the intake tract at higher throttle openings, and there isn't much you can do about that.



I drove one around like a normal car, the only difference was like you noticed, you have to be accelerating or decelerating, if you just try to cruise then it shakes the fillings out of your teeth. It was quite oderiferous at stoplights.



but at the same time it fires right up and will idle @1100rpm cold with no choke...

12aJBridgeport 02-24-2010 01:11 PM

Would using the 2nd gen n/a rotor housings with the exhaust diffuser to dull the exhaust sharpness tone be do-able? How much restriction does that diffuser really create?



Also how about a smaller intake port to increase intake velocity and reduce some overlap. Say 38mm?

j9fd3s 03-13-2010 01:42 PM


Originally Posted by 12aJBridgeport (Post 838894)
Would using the 2nd gen n/a rotor housings with the exhaust diffuser to dull the exhaust sharpness tone be do-able? How much restriction does that diffuser really create?



Also how about a smaller intake port to increase intake velocity and reduce some overlap. Say 38mm?



in moving houses, i got a chance to drive mine some more. mine is MFR port style. smaller ports would probably help its manners, but really its not that bad though.



noise isn't really even too bad, the thing is really that the college kids have never seen a car that isn't domesticated. its like having a tiger in a herd of veal cows....

hksthor 05-07-2010 12:46 AM

whats the spec of your exhaust your using i had good results with 2 1/4 inch primaries to the diff into a colector and 3 inch over the diff with a 3 inch dumpy type muffler sounded good pulled smooth

j9fd3s 05-08-2010 03:04 PM


Originally Posted by hksthor (Post 840555)
whats the spec of your exhaust your using i had good results with 2 1/4 inch primaries to the diff into a colector and 3 inch over the diff with a 3 inch dumpy type muffler sounded good pulled smooth



i've been running a pacesetter into a 3" glass pack into a borla. the new system is RB header, into 3" by the axle into the same borla

Lynn E. Hanover 05-15-2010 08:55 AM


Originally Posted by 12aJBridgeport (Post 838894)
Would using the 2nd gen n/a rotor housings with the exhaust diffuser to dull the exhaust sharpness tone be do-able? How much restriction does that diffuser really create?



Also how about a smaller intake port to increase intake velocity and reduce some overlap. Say 38mm?





I found that the Periphery port engine was more tractible than the bridgeported side port engine. The Pport we drove around like a stock car. The side port had to be towed around the paddock. This was with Mandevile modified housings with huge rectangular ports and very late closing. It had no power at all at low speed. It had poor hot starts and very poor starting in cold weather. Like propane torch on the intake manifold cold starting.



Most streetable designs had small periphery ports, and had good performance.



If you port it so it runs great at 10,000 RPM it may not be any fun at all below 6,000 RPM. When it comes to poor low speed performance, nothing beats a Pport. We usually ran a 60 MPH first gear, and if the pace lap was slow we were screwed on the start. So on short tracks we had a 5:12 rear gear for the Speedway quick change.



An intake port with about 30% more area than the stock exhaust port and about the same shape, should work fine.



Two features of the Pport combine to ruin low speed (streetable) performance. Just like a late closing intake valve in a piston engine, the late closing intake port in a rotary determines low speed performance.



Later closing means that the piston, or rotor is past bottom dead center and the cylinder or chamber volume is decreasing, so some of the intake volume is pushed back into the intake system and is not trapped in the chamber to be compressed. So, less volume being compressed into a fixed headspace means lower effective compression ratio.





The engine (in effect) has become smaller in displacement, has it not?



At high speed the mass of the inlet gasses over-fill the chamber and are then trapped to be compressed. Volumetric efficiencies in excess of 100% are possible. The engine has become larger in displacement (in effect) has it not?



Early intake closing does the reverse at lower engine speeds. Traps more volume in the cylinder or chamber after port closing. More volume is compressed into the the fixed headspace, and the effective compression ratio goes up. The engine gets larger in displacement (in effect). Heat of compression is higher, and gets you better hot and cold starting performance. Heat of compression is higher and fuel vaporizes more effectively. Of course high RPM power is reduced.





The second problem is the overlap. Where intake and exhaust ports are open at the same time. The unobstructed ports flow well in both directions, so any pressure developed in the exhaust system will cause spent and some times still burning gasses to gleefully flow right back into the engine and up into the intake port. Ouch!!!!



One way to reduce this problem is to use a bit smaller primary header tubing diameter, and longer runs before the collector. This gives higher velocity in the header, and puts each pulse further along the tube per unit of time. I would try running both tubes to the rear of the car before collecting as in early RX-2 and 3 racers. 102" of primary was the rule.



A well designed muffler is important as well. Less heat damage will be seen with the muffler at the end of the system. Mechanical damage may be increased. The hammering that rotaries do so well.



So don't move the exhaust port closing point up any at all. You could go a bit wider, and open a few degrees earlier if you just cannot put the die grinder down. Or,leave it stock. Keep the intake open point as late (high)as possible. And intake closing point as early as is possible. That means a short wide intake port. Less is more when it comes to good low end performance. The periphery intake port is much more effective than any side port or even a bridge port, so street performance will be great.



Lynn E. Hanover

hksthor 05-28-2010 02:45 AM


Originally Posted by Lynn E. Hanover (Post 840775)
I found that the Periphery port engine was more tractible than the bridgeported side port engine. The Pport we drove around like a stock car. The side port had to be towed around the paddock. This was with Mandevile modified housings with huge rectangular ports and very late closing. It had no power at all at low speed. It had poor hot starts and very poor starting in cold weather. Like propane torch on the intake manifold cold starting.



Most streetable designs had small periphery ports, and had good performance.



If you port it so it runs great at 10,000 RPM it may not be any fun at all below 6,000 RPM. When it comes to poor low speed performance, nothing beats a Pport. We usually ran a 60 MPH first gear, and if the pace lap was slow we were screwed on the start. So on short tracks we had a 5:12 rear gear for the Speedway quick change.



An intake port with about 30% more area than the stock exhaust port and about the same shape, should work fine.



Two features of the Pport combine to ruin low speed (streetable) performance. Just like a late closing intake valve in a piston engine, the late closing intake port in a rotary determines low speed performance.



Later closing means that the piston, or rotor is past bottom dead center and the cylinder or chamber volume is decreasing, so some of the intake volume is pushed back into the intake system and is not trapped in the chamber to be compressed. So, less volume being compressed into a fixed headspace means lower effective compression ratio.





The engine (in effect) has become smaller in displacement, has it not?



At high speed the mass of the inlet gasses over-fill the chamber and are then trapped to be compressed. Volumetric efficiencies in excess of 100% are possible. The engine has become larger in displacement (in effect) has it not?



Early intake closing does the reverse. Traps more volume in the cylinder or chamber after port closing. More volume is compressed into the the fixed headspace, and the effective compression ratio goes up. The engine gets larger in displacement (in effect). Heat of compression is higher, and gets you better hot and cold starting performance. Heat of compression is higher and fuel vaporizes more effectively.





The second problem is the overlap. Where intake and exhaust ports are open at the same time. The unobstructed ports flow well in both directions, so any pressure developed in the exhaust system will cause spent and some times still burning gasses to gleefully flow right back into the engine and up into the intake port. Ouch!!!!



One way to reduce this problem is to use a bit smaller primary header tubing diameter, and longer runs before the collector. This gives higher velocity in the header, and puts each pulse further along the tube per unit of time. I would try running both tubes to the rear of the car before collecting as in early RX-2 and 3 racers. 102" of primary was the rule.



A well designed muffler is important as well. Less heat damage will be seen with the muffler at the end of the system. Mechanical damage may be increased. The hammering that rotaries do so well.



So don't move the exhaust port closing point up any at all. You could go a bit wider, and open a few degrees earlier if you just cannot put the die grinder down. Or,leave it stock. Keep the intake open point as late (high)as possible. And intake closing point as early as is possible. That means a short wide intake port. Less is more when it comes to good low end performance. The periphery intake port is much more effective than any side port or even a bridge port, so street performance will be great.



Lynn E. Hanover





wow awesome lyn what sort of intake and exhuast timing would be good for him to use he could use almost factory open and close on the intake could he not?


All times are GMT -5. The time now is 03:22 AM.


© 2024 MH Sub I, LLC dba Internet Brands