Rew Swap In An Fc
10-02-2007, 07:33 PM
#91
Senior Member
Join Date: Feb 2003
Location: Calgary
Posts: 564
Mines running, I made my own mount setup, very stable, the halbridge has less rock than it did with the FC motor and mounts. I grafted the emissions harness's into the car, so its basically FD from the firewall forward. And the sensor check fuction is working as well. Its not a bad swap , its just all the little things that need to be done, like water pump inlet angling, change oil lines, etc etc. My car was a big single car, so I had done away with alot of the stock FD and FC stuff anyway which means fabricating new things to hold aftermarket stuff.. I have no rats nest whatsoever, I made adapters for the FD primary fuel rail to 8-an connections, boost and pre throttle aid distribution blocks and stuff like that, which just takes time.. A stock FD setup would drop in pretty fast..
10-20-2009, 06:04 PM
#92
Junior Member
Join Date: Oct 2009
Location: Wellington, NZ
Posts: 3
I seriously hope you are still making this mate??? if so please send me an email robertmac@xtra.co.nz !!!! I tried your website but can't seem to get through to it!
10-20-2009, 06:39 PM
#93
Super Moderator
Thread Starter
Join Date: Sep 2002
Location: Savannah, Ga
Posts: 2,763
I seriously hope you are still making this mate??? if so please send me an email robertmac@xtra.co.nz !!!! I tried your website but can't seem to get through to it!
Sorry about the site being down. Ive changed hosting, and am working on a new site design as well. Should have it back up in another week or so. Ill email you shortly.
04-06-2010, 11:35 PM
#94
Junior Member
Join Date: Apr 2010
Posts: 1
How can you tell its from a j-spec? If it really is, I may need to go pay a "visit" to the guy who I got it from...
More than happy to make a set of mounts for you, and for anyone else. Heres the thread I posted in the for sale section offering these mounts.
More than happy to make a set of mounts for you, and for anyone else. Heres the thread I posted in the for sale section offering these mounts.
this works for a 13B REW engine and transmission full swap with TT???
04-07-2010, 12:07 PM
#95
Super Moderator
Thread Starter
Join Date: Sep 2002
Location: Savannah, Ga
Posts: 2,763
The 13B-REW will fit with all OEM accessories, including the stock twins. The transmission should fit just fine, but I used a TII transmission. I prefer the push type clutch assembly on the 2nd gen trans over the pull type on the 3rd gen trans. The only real difference between S5 TII and FD transmissions are the addition of dual cone synchros on 1st and 2nd gear(I believe, its been a while though), and the previously mentioned clutch. I havent measured, so I cant be 100% sure the shifter will be in the proper spot with the 3rd gen trans.
04-13-2010, 02:15 PM
#96
Member
Join Date: Apr 2010
Location: veedersburg In
Posts: 80
I just placed my order but if you could help me with some other stuff I need to buy. I have the full motor trani front mount Intercooler and mounts now not sure off hand what else I need but if someone could give me a list and where I can get all of it would be great...
Thread
Thread Starter
Forum
Replies
Last Post
mazdaspeed7
RX-7 & RX-8 Parts For Sale & Wanted
26
02-23-2007 11:59 PM
mazdaspeed7
RX-7 & RX-8 Parts For Sale & Wanted
2
12-12-2005 09:25 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)