The setup.....

The result...

eat more wheaties!



take a jack handle and hit the breaker bar with it



mike

Thats angle iron... https://www.nopistons.com/forums/pub...DIR#>/ohmy.png We also have an impact gun, but I think the adapter is robbing most the power(1/2 to 1 inch adapt)

Quick suggestion as well, use the impact, make sure the compressor is fully charged. Take the impact and fill the air inlet with WD-40 (which I see you have in the pictures) . Pound on the nut with the impact gun untill you hear the compressor kick on again. Stop wait for the compressor to fill completely and start again. try this 3x, on the 4th try, hit the impact to tighten and hit it about 30 seconds. Wait for the compressor to fill and try removal with the WD-40 trick again.





The WD-40 is similar to the ATF trick for a won't start. It causes higher compression of the impact gun and also oils the internal parts at the same time.

first thing i've gotta ask, who in their right mind works on cars in bare feet? https://www.nopistons.com/forums/pub...IR#>/wacko.png



ya'll need to rethink you're ghetto engineering you've got going on there https://www.nopistons.com/forums/pub...1047683561.gif I love it.

Like I said you need a puller, that is the way I always get mine off, WORK SMARTER NOT HARDER lol

actually not even at the puller stage yet, they still havent got the nut off https://www.nopistons.com/forums/pub...R#>/unsure.png

LOL oh my bad, mixing AIM convo's with posts. I think they finally got it off, or I had one really fucked up aim convo. Maybe I should sleep.

no it is not off yet...phins you need to sleep after drinking haha

HA HA what the ****, I thought we were talking about the flywheel itself, that was one really fucked up convo then. Ok the nut, I have a huge ass impact from snap-on so my life is a little easier. However if it's really bac, you can get your self a can of "freeze-it" it's liquid nitrogen, don't let 1revvin near it he will mame himself (joke). Get a torch, heat the living **** out of the flywheel, the take the freeze it and freeze the nut and hit her with the impact or breaker bar.



This is how we used to have to remove valve seats in Aircraft engines, it's a lot of fun, except we had a big 'ol oven to toss the heads in.

u need to have a bar with 2 holes drilled into it that fit over the flywheel to hold it from moving while u turn the nut. and yes, y are u barefoot?

ha ha awesome, he's barefoot. Yea, ILUVMY88 made a bar for me, however with the impact we did not need it.

The bare does have 2 holes, and it did hold it still untill I pulled on the breaker bar and picked up 300#s+180#s+180#s... Ask nick why the hell he is barefoot, no idea.. https://www.nopistons.com/forums/pub...1047683785.gif

haha i was barefoot cuz i was cleaning the engine bay, i.e. hoses, spray bottles, rags.... didn't want to completely wreck my only pair of shoes. oh yeah we hillbillies up here in minnesotah

try pulling the nut



mike

https://www.nopistons.com/forums/pub...>/rolleyes.gif







Speak for yourself https://www.nopistons.com/forums/pub...#>/biggrin.png

HA HA, bet you say that to all the ladies. https://www.nopistons.com/forums/pub...1047683785.gif

HA HA, bet you say that to all the ladies. https://www.nopistons.com/forums/pub...1047683785.gif [/quote]

yeah it doesnt work well there either



mike

ok so i'm asking mike for some help on this situation on aim "MIKE HOW DO I GET THIS DAMN NUT OFF!!!?" this man comes back 2 seconds later with porn link... this guy cracks me up hard..

Yea I would have done the same thing, but prolly told you that you at least have to buy me dinner first LOL

https://www.nopistons.com/forums/pub...1047683785.gif https://www.nopistons.com/forums/pub...1047683785.gif https://www.nopistons.com/forums/pub...1047683785.gif https://www.nopistons.com/forums/pub...1047683785.gif https://www.nopistons.com/forums/pub...1047683785.gif

thats mike for ya

well ask how you get yer nuts off and i'll tell ya



mike

propane torch + penetrating oil + good expensive thunder gun = nut come off

yo go ghetto like me. I use a chisel and a ******* hammer. lol I hit a corner and make a groove and keep hitting that bitch till she comes off. I dont recomend my way unless u want a fucked up nut lol