it was cheap! and its modded

where are the engine bay pics

j9fd3s: i'm bending my car

three se7ens: youre bending your car?

j9fd3s: yah it got hit between the taillights

j9fd3s: so ive pulled the lights out and i'm pulling it back

j9fd3s: hurts!

three se7ens: lol

j9fd3s: the edge digs in

three se7ens: i just got a mental picture of you with with your feet on the bumper, hands on the sheet metal there and just pulling like crazy...

three se7ens: i laughed, and wished someone there had a camera

j9fd3s: haha

j9fd3s: thats exactly what i was doing!

j9fd3s: i need a block of wood

three se7ens: heres an idea

three se7ens: put a block of wood inside the car, tie a rope to it

three se7ens: tie the other end of the rope to your waist, and run full speed away from the car

three se7ens: viola. you have an oversized slide hammer

j9fd3s: lol

j9fd3s: i should just hit it with a really big hammer and hope all the bondo falls off

there is something i like about those broken tails, i am not sure what it is https://www.nopistons.com/forums/pub...1047683561.gif

the mighty 13b 6 port!

wtf does it need all that ignition for ??? lol

i told him earlier, that the msd boxes are worth more then the car, he said that and the cage is why he bought it.

i didn't notice the cage. ship it to NJ. i have dibs

j9 stop slacking, where are cage pics?!

does kahren have to slap a bitch???

lol only half of the cage is in the car

good job j9, now rip out that crappy stock 6port and go with a 2 port https://www.nopistons.com/forums/pub...#>/biggrin.png

updatery!

That's very nearly not bad! Seriously though, that's impressive getting it like that from what it was. For some reason it looks really clean in that first pic, maybe it's because the side protection strips are gone.



Mark

nope thats not quite it, you'll see in the next couple weeks

the car after parking it near his local hot rod shop..

That's a pretty good looking car ^. Anyone know what wheels are on it? They almost look like panasports but a litle different.



Mike your car isn't all that bad either https://www.nopistons.com/forums/pub...IR#>/smile.png

lol, they should be wantanabe's



theres also these, they look ok i think, price is right too



http://www.good-win-racing.com/mazda/miata/60-1043.html

hmm... there is something about the silver cars wheels that looks better. The ones on that miata aren't bad but that silver car just looks good to me for some reason..



Thanks for the info Mike!

Is this pic for real?!?!?! or is it photoshopped? I'd love to have this done to my car, but that would be ALOT OF WORK!!!

photochop https://www.nopistons.com/forums/pub...#>/biggrin.png



fb would be easy compared to some cars, most of the pillars are just extrusions....

those tires look like they belong ona school bus

maybe the lack of center garnish? like the SAs.

You'd probably have to be a midget to drive it, though.

new pics. painted window mouldings, rb muffler, jdm hks afm bracket

that air filter was on a 3 rotor!

I like your FB. I love to see people modifying 1st gens. I wish someone in my area had a FB, but they all have honda's!!

yeah i think ive seen like 2-3 rx's in oregon.

what front bumper is that?



i need more pics of it, if i dont end up repainting the whole car dark orange i will end up sticking to silver.

it weighs in @2500lbs even, with a full tank

I know what that car needs!!!! https://www.nopistons.com/forums/pub...IR#>/smile.png

these?

That is cool....I have always wanted to see a twin setup on a first gen. Especially a 4 rotor twin set-up...drool.



Maybe one day...

4 rotor is a teeny bit out of budget. the twins though arent



so far....



manifold + dp $400

turbine housings (oddball jdm greddy stuff) $300

2 td05-16g's $800



now i need fuel....

are you trying to snap that car in half ??? haha

YES!

HAHAHAHA....well better stiffen that fram then. I think that my fuel system was around 1k. That should be more than enough for what you are looking at. Are you running a carb? If not don't forget the EMS and tuning https://www.nopistons.com/forums/pub...IR#>/smile.png I would love to see this thing...

so far for fuel ive got um a chipped 12at ecu, and a greddy aic. i also need intercooling

IC is cheap...well in comparrison to the rest. 167 for the FMIC, 300-400 for the pipe, welding and couplers... Just takes a few hours to fab.



My amounts might be a little high...I went with 3" al though...

ive got a lot of it laying around, 2.5" steel, its easy. depending on what motor i use it would be neat to do 3" al though